Micom ALSTOM P341, Technical Data Sheet

Page: 25 / 62

P341 Technical Data Sheet
23
P341 Software versions 36 & 71J
CT and VT ratios
Main VT Primary: 100...1000000 V
Main VT Sec'y: 80...140
(100/120 V) 320…560 V (380/480 V)
C/S VT Primary:
100 V…1 MV
C/S VT Secondary: 80…140 V
VN VT Primary (P342/3): 100…1000000 V
VN VT Secondary (P342/3):
80…140 V
(100/120 V) 320…560 V (380/480 V)
PH CT Polarity:
Standard, Inverted
Phase CT Primary: 1 A…50 kA
Phase CT Sec'y Sec'y : 1 A/5 A
ISen CT Polarity:
Standard/Inverted
ISen CT Primary: 1 A…60 KA
ISen CT Sec’y: 1 A/5 A
Sequence of event recorder (record
control)
Alarm Event: Disabled/Enabled
Relay O/P Event: Disabled/Enabled
Opto Input Event: Disabled/Enabled
General Event: Disabled/Enabled
Fault Rec Event: Disabled/Enabled
Maint Rec Event: Disabled/Enabled
Protection Event: Disabled/Enabled
DDB 31 - 0: (up to):
DDB 2047 - 2016:
Binary function link strings, selecting which
DDB signals will be stored as events, and
which will be filtered out.
Oscillography
(disturbance recorder)
Duration: 0.10…10.50 s
Trigger Position: 0.0…100.0%
Trigger Mode: Single/Extended
Analog Channel 1: (up to):
Analog Channel 8:
Disturbance channels selected from:
IA/IB/IC/VA/VB/VC/VN/ISensitive/Frequency
V Checksync
Digital Input 1:
(up to):
Digital Input 32:
Selected binary channel assignment from
any DDB status point within the relay (opto
input, output contact, alarms, starts, trips,
controls, logic…).
Input 1 Trigger: No Trigger/Trigger/LH (Low to
High)/Trigger H/L (High to Low)
(up to):
Input 32 Trigger: No Trigger/Trigger
L/H/Trigger H/L
Measured operating data
(measure’t setup)
Default Display:
Access Level
3Ph + N Current
3Ph Voltage
Power
Date and Time
Description
Plant Reference
Frequency
Local Values:
Primary/Secondary
Remote Values: Primary/Secondary
Measurement Ref: VA/VB/VC/IA/IB/IC
Measurement Mode: 0/1/2/3
Fix Dem Period: 1…99 mins
Roll Sub Period: 1…99 mins
Num Sub Periods: 1…15
Remote2 Values: Primary/Secondary
Communications
RP1 Address:
(Courier or IEC 870-5-103)
:
0…255
RP1 Address:
(DNP3.0):
0…65534
RP1 Address:
(MODBUS):
1…247
RP1 InactivTimer:
1…30 mins
RP1 Baud Rate:
(IEC 870-5-103):
9600/19200 bits/s
RP1 Baud Rate:
(MODBUS, Courier):
9600/19200/38400 bits/s
RP1 Baud Rate:
(DNP3.0):
1200/2400/4800/9600/19200/ 38400 bits/s
RP1 Parity:
Odd/Even/None
(MODBUS, DNP3.0)
RP1 Meas Period: 1…60 s
(IEC 870-5-103)
RP1 PhysicalLink:
Copper (EIA(RS)485/K bus) or Fiber Optic
RP1 Time Sync:
Disabled/Enabled
MODBUS IEC Timer: Standard/Reverse
RP1 CS103Blocking:
Disabled
Monitor Blocking
Command Blocking
RP1 Port Config:
(Courier):
K Bus
EIA485 (RS485)
RP1 Comms Mode:
(Courier):
IEC 60870 FT1.2
IEC 60870 10-Bit No parity
Note:
If RP1 Port Config is K Bus the baud
rate is fixed at 64 kbits/s
Optional Ethernet port
NIC Tunl Timeout: 1...30 mins
NIC Link Report: Alarm, Event, None
NIC Link Timeout: 0.1...60 s
Optional additional second rear
communication (rear Port2 (RP2))
RP2 Port Config:
EIA(RS)232
EIA(RS)485
K-Bus