background image

 

20 

 
SECTION E: For Operators with Interface Modules or Logic boards 

 
 
 
 
 

Installation Safety Precautions 
 
WARNING:  MICANAN  MK00649  NEMA-1,  MK00650  NEMA-4  and  FRABA  MK00697  NEMA  4/4X  infrared  photo 
systems  are  for  use  only  with  MICANAN  logic  board  operators  or  relay  logic  operators  equipped  with  the  Micanan 
failsafe  interface  module.  Use  of  this  device  on  other  than  recommended  operators  can  lead  to  severe  or  fatal  injury. 
Follow these instructions carefully. 

 

 
IMPORTANT: 

For  momentary  activation  on  close,  the  MICANAN  photobeams  (or  a  Micanan  2-wire  monitored  edge), 

must  be  installed  as  part  of  the  operator  system.

  If  a  Micanan  2-wire  monitored  edge  or  the  MICANAN  infrared 

photobeam  system  is  not  installed  (or  not  operating  correctly),  the  operator  will  only  operate  in  fault  mode  (constant 
pressure to close).

 

 
READ and FOLLOW all installation instructions. 
1.

 

Before installing the photo beam, read the door or gate operator’s instruction manual fully, so you are aware of all of the 
unit’s functions and features. 

2.

 

Wear protective gloves and eye protection when using tools. 

3.

 

Before installing photo beam, disconnect all power to door operator to prevent unintended operation and have the door full 
open or close. 

4.

 

Do not reconnect power to the door or gate operator until instructed to do so. 

5.

 

Only install photobeams on a properly functioning door or gate operator. 

6.

 

Installation and wiring must comply with local building and electrical codes. This device is not intended and must not be 
installed in an explosive environment.   

 
WARNING: Keep fingers and other body parts away from all moving parts of the door and gate operator system while 
the system is being operated. 
 
WARNING:  To  prevent  unintended  operation,  disconnect  power  to  the  door  or  gate  operator  prior  to  installing  the 
photobeam system. 

 

MICANAN N-1 PHOTOCELL (MK00649) 

Note: The MK00649 photocell system has a maximum range of 24 ft. Sun visor protector optional. 

 
Installation 
Note:  Photo  beams  should  be  mounted  as  close  to  the  door  track  inside  the  door  to  offer  maximum  entrapment 
protection. 

Wall installation: 

 

1.

 

Select a location on the wall no more than 6 inches from the floor to install wall mounting brackets on the left and right 
side of the door. Both brackets must be mounted at the same height for proper alignment. 

2.

 

Drill holes in the wall and attach brackets to the wall using screws and nails provided as shown in Fig. 1. 

 
 
 
 
 
 
 
 
 
 

 

 

INSTALLATION OF MICANAN  N-1 OR N-4 PHOTOCELLS 

Summary of Contents for PRO-LH








































Reviews: