background image

 

 

 
 

PRO-LJ and PRO-LH medium duty jackshaft operators are designed for commercial high lift, vertical lift, rolling doors and 
rolling grilles provided that doors are driven by a drive shaft with low duty cycles. Model PRO-LH is essentially the same as 

model PRO-LJ with the exception that the PRO-LH operator incorporates a chain hoist for manual operation of the door.  
 

STANDARD OPERATOR WEIGHT

45-50 LBS  

  

MOTOR

: Intermittent duty 1000 RPM motor with high starting torque. 

- Thermally protected by a built-in thermostat that cuts power to the motor and control circuit when overheating.  
- Horsepower: 1/2HP 

- Voltage: 115V  1-phase (60Hz)         220V 1-phase (50Hz) 

    

 

 

   230V  1-phase (60Hz)         380V 3-phase (50Hz) 

 

 
 

 

 

REDUCTION

:   Primary: (4L) V-belt and pulleys (1.5” to 7” diameter), Secondary: #41 chain and sprockets 

 

OUTPUT SHAFT SPEED

: 58 RPM

  

 

 

BRAKE

 : Solenoid actuated drum and brake shoe braking system to prevent coasting and maintain door position. 

 

WIRING TYPE (3 OPTIONS)

Option 1: 

Limited Duty logic board Smart 5.0 (UL325 (2010) compliant)

. Note: Micanan compatible primary entrapment  

device must be connected for B2 or TS (momentary or timer activation on close) feature. 

Option 2: 

Relay logic controls with Interface Module (UL325 (2010) compliant

). C2 Standard factory wiring (constant  

pressure on close, momentary contact on open and stop). If momentary contact on close (B2) wiring is desired, connect 
loose “purple” wire to terminal #5. Note: Micanan compatible primary entrapment device must be connected for B2 

(momentary activation on close) feature. 

Option 3: 

Standard relay logic controls (not UL325 (2010 compliant, not available in US) 

C-2 Wiring constant  

pressure on 

close, momentary contact on open and stop. NOTE: If momentary contact on close (B2) wiring is desired, 

connect 

 loose “purple” wire to terminal #5. 

 

TRANSFORMER

: 24VAC control circuit, supplies power to drive control relays with 15VA power available for external  

devices. 

 

LIMIT ADJUSTMENT

: 4 micro switches that control door travel. These limit switches are activated by fully adjustable screw  

type cams.  

 

EMERGENCY DISCONNECT

: Floor level cable disconnect system with electrical cut-out feature allows person to manually  

operate the door by hand (PRO-LJ) or by chain hoist (PRO-LH) in case of emergency. 

 

CLUTCH

: Adjustable friction clutch to minimize damage to door operator, door or vehicles when obstruction occurs. 

 

OPERATOR DIMENSIONS

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

PRO-LJ, PRO-LH SPECIFICATIONS 

IMPORTANT NOTE 

THIS MEDIUM DUTY OPERATOR IS DESIGNED TO OPERATE 

A MAXIMUM OF 15 COMPLETE CYCLES PER HOUR. 

Summary of Contents for PRO-LH








































Reviews: