Mi-T-M GEN-3000-iMM0, Operator'S Manual

Page: 26 / 116

Operating the Generator
26 Operator’s Manual
OPERATION
CABLE SIZE:
When a long electric extension cord is used to connect an appliance or tool to the generator, a certain amount of voltage
drop or loss occurs in the extension cord which reduces the effective voltage available for the appliance or tool. The
chart below has been prepared to illustrate the approximate voltage loss when an extension cord of 300 feet (approx.
100 meters) is used to connect an appliance or tool to the generator.
Equipment damage can result from low voltage. Therefore, to prevent excessive voltage drop between the generator
and the equipment, the cable should be of adequate gauge for the length used. The cable selection chart gives the
maximum cable lengths for various gauges of wire which can adequately carry the loads shown.
PARALLEL CONNECTION:
First, connect the 2 inverters with 2 parallel cables as per the drawing below. Then start the inverters one at a time. At
this time, the total rated power will be 3000W. The parallel cables must be connected to parallel outlet with the same
color for each inverter.
Note: Ensure the cables are connected to the inverters correctly. If they are connected incorrectly, the inverters will not
output any power and will need to be switched off and then on again after they are correctly connected. DO NOT
connect or disconnect the parallel cables while the engine is running.
CURRENT LOAD IN WATTS MAXIMUM CABLE LENGTH (FEET)
IN AMPS 120 VOLTS 240 VOLTS #8 WIRE #10 WIRE #12 WIRE
#14 WIRE #16 WIRE
2.5 300 600 1000 600 375 250
5 600 1200 500 300 200 125
7.5 900 1800 350 200 125 100
10 1200 2400 250 150 100 50
15 1800 3600 150 100 65
20 2400 4800 175 125 75 50
25 3000 6000 150 100 60
30 3600 7200 125 65
40 4800 9600 90
IDLE CONTROL
CONTROL DE FLOJEAR
VITESSE AU RALENTI
PARALLEL
OPERATION OUTLETS
PRISE DE FONCTIONNEMENT
EN PARALLÈLE
SALIDAS DE OPERACIONES
PARALELAS
ON
OFF
AC RESET
RÉARMEMENT DU
COURANT ALTERNATIF
REINICIO DE CA
OVERLOAD
SOBRECARGA
SURCHARGE
OUTPUT
ENCENDIDA
PUISSANCE
FOURNIE
AC 120V
USB
DO NOT CONNECT OR DISCONNECT THE PARALLEL
CABLES WHILE THE ENGINE IS RUNNING.
NO CONECTE O DESCONECTE LOS CABLES PARALELOS
MIENTRAS QUE EL MOTOR ESTÁ FUNCIONANDO.
NE PAS CONNECTER OU DÉCONNECTER LES CÂBLES
PARALLÈLES LORSQUE LE MOTEUR EST EN MARCHE.
MAIN CIRCUIT
BREAKER
CORTACIRCUITOS
PRINCIPAL
DISJONCTEUR
DE SECTEUR
20 AMP
AC BREAKER
CORTACIRCUITOS
DISJONCTEUR
DC 12V 8.3A
NEUTRAL FLOATING
NEUTRO FLOTANTE
NEUTRE FLOTTANT
120 VOLT - 30 AMPS
MAX 23A
SYSTEM FLOATING
COURANT CONTINU VARIABLE
RÉSEAU FLOTTANT
IDLE CONTROL
CONTROL DE FLOJEAR
VITESSE AU RALENTI
PARALLEL
OPERATION OUTLETS
PRISE DE FONCTIONNEMENT
EN PARALLÈLE
SALIDAS DE OPERACIONES
PARALELAS
ON
OFF
AC RESET
RÉARMEMENT DU
COURANT ALTERNATIF
REINICIO DE CA
OVERLOAD
SOBRECARGA
SURCHARGE
OUTPUT
ENCENDIDA
PUISSANCE
FOURNIE
AC 120V
USB
DO NOT CONNECT OR DISCONNECT THE PARALLEL
CABLES WHILE THE ENGINE IS RUNNING.
NO CONECTE O DESCONECTE LOS CABLES PARALELOS
MIENTRAS QUE EL MOTOR ESTÁ FUNCIONANDO.
NE PAS CONNECTER OU DÉCONNECTER LES CÂBLES
PARALLÈLES LORSQUE LE MOTEUR EST EN MARCHE.
MAIN CIRCUIT
BREAKER
CORTACIRCUITOS
PRINCIPAL
DISJONCTEUR
DE SECTEUR
20 AMP
AC BREAKER
CORTACIRCUITOS
DISJONCTEUR
DC 12V 8.3A
NEUTRAL FLOATING
NEUTRO FLOTANTE
NEUTRE FLOTTANT
120 VOLT - 30 AMPS
MAX 23A
SYSTEM FLOATING
COURANT CONTINU VARIABLE
RÉSEAU FLOTTANT
AC 120V/20A
AC BREAKER
AC 120V/30A