background image

Instructions

Models MGFP39/44/49

Equipped with Safety Pilot System / Remote Control Valve

Low profile or pan 

burners are not 

allowed for use in 

these units without a 

metal base

Do not store or use gasoline or other 

flammable vapors and liquids in the 

vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS:

• 

Do not try to light any appliance.

• 

Do not touch any electrical switch; do 

not use any phone in your building.

• 

Immediately call your gas supplier from 

a neighbor’s phone and follow the gas 

supplier’s instructions.

• 

If you cannot reach your gas supplier, 

call the fire department.

Installation and service must be 

performed by a qualified installer, service 

agency, or the gas supplier.

WARNING:

If the information in these instructions is 

not followed exactly, a fire or explosion 

may result causing property damage, 

personal injury or death.

REV 1/7/21

B-vented Gas Appliances with Masonry Firebox

The logs and burner must be permanently installed in and 

are only for use in this appliance. This appliance must be 

connected to a working flue meeting the requirements of 

the ANSI Z21.50 standard.

Solid-fuels shall not be burned in this appliance.

This appliance must be vented vertically through the 

roof. This appliance is not for installation in manufactured 

or mobile homes. The installation, including provisions 

for  combustion,  ventilation  air,  and  required  minimum 

permanent vent opening, must conform with the National 

Fuel Gas Code (ANSI Z223.1/NFPA 54) and applicable 

local building codes. 

This gas appliance is designed to 

burn with yellow flames; thus adequate ventilation is 

absolutely necessary.

IMPORTANT:

 READ THESE INSTRUCTIONS

CAREFULLY BEFORE STARTING

INSTALLATION OF THIS APPLIANCE. 

WARNING:

This gas appliance must not be connected to a chimney 

fuel servicing a solid fuel burning appliance.

Do not store gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Report No.

08-154

ICC Evaluation Services 

Report No. 2401

This appliance is only for use with the type 

of gas indicated on the rating plate. This 

appliance is not convertible for use with 

other gases, unless a certified kit is used.

Installer:

 Leave these instructions with the consumer.

Consumer:

 Retain for future reference.

Equipped with Safety 

Pilot System / Remote 

Control Valve

Summary of Contents for MASON-LITE MGFP39








































Reviews: