Mettler Electronics Sys*Stim 294 Instruction Manual Download Page 44

Page: 44 / 44

Mettler Electronics Corp.—

Rev.F_09/13/17

2702

V Trode –2" diameter round electrodes with lead wires, case of ten
packages (four electrodes/pkg.)

2703

V Trode –2.75" diameter round electrodes with lead wires, case of 10
packages (four electrodes/pkg.)

2704

V Trode –2" x 4" oval electrodes with lead wires, case of 10 packages
(four electrodes/pkg.)

2705

V Trode –2" square electrodes with lead wires, case of 10 packages
(four electrodes/pkg.)

7293

Detachable U.L. listed, hospital–grade line cord

Three-shelf mobile cart for all Sonicator Plus products. Holds unit on
the top shelf with lower shelves for accessories.

9900

Electrical Stimulation & Ultrasound Pocket Guide

by Michelle H.

Cameron. Designed for use with the Sys*Stim 294.

Summary of Contents for Sys*Stim 294













































Search results

Summary of Contents for Sys*Stim 294

Reviews:

Related manuals for Sys*Stim 294

Brands by name

Popular brands

Mettler Electronics Sys*Stim 294, Instruction Manual

Search results

Summary of Contents for Sys*Stim 294

Reviews:

Related manuals for Sys*Stim 294

Brands by name

Popular brands