manualshive.com logo in svg

Mettler Electronics Sys*Stim 294, Instruction Manual

Share
Download
Mettler Electronics Sys*Stim 294 Instruction Manual Download Page 14

Mettler Electronics Corp.—

 

Rev.F_09/13/17 

14

 

 

Electrode Cable Connections

 

Figure 3.2— Sys*Stim 294, Front View— 

Electrode Cable Connections 

 

3.2 EMC Guidance 

CAUTION:

 

Medical Electrical Equipment needs special precautions regarding Electromagnetic 
Compatibility (EMC) and needs to be installed and put into service according to the EMC 
information provided in the following tables. 

 

Portable and mobile Radio Frequency (RF) communications equipment can affect Medical 
Electrical Equipment. 

Accessories:

 

Hospital Medical grade power cord of a maximum length of 120 inches 

 

WARNING:

 

The use of accessories, other than those specified, except those supplied or sold by Mettler 
Electronics Corp., as replacement parts for internal or external components, may result in 
increased EMISSIONS or decreased IMMUNITY of the Sys*Stim 294. 

Guidance and manufacturer’s declaration – electromagnetic emissions 

The Sys*Stim 294 is intended for use in the electromagnetic environment specified below.  The customer or 

the user of the Sys*Stim 294 should assure it is used in such an environment. 

Emissions Test 

Compliance

Electromagnetic environment-guidance 

RF emissions 

CISPR 11 

Group 1 

The Sys*Stim 294 must emit electromagnetic energy in order to 

perform its intended function.  Nearby electronic equipment 
may be effected. 

RF emissions 

CISPR 11 

Class B 

The Sys*Stim 294 is suitable for use in all establishments other 

than domestic and those directly connected to the public low-
voltage power supply network that supplies buildings used for 
domestic purposes. 

Harmonic emissions 

IEC 61000-3-2 

Applicable 

Voltage 
fluctuations/flicker 
emissions 

IEC 61000-3-3 

Applicable 

 

Summary of Contents for Sys*Stim 294













































Reviews:

No comments

Brands by name

Popular brands

Load more brands