manualshive.com logo in svg

Mettler Electronics Sys*Stim 294, Instruction Manual

Share
Download
Mettler Electronics Sys*Stim 294 Instruction Manual Download Page 23

Sys*Stim 294 Instruction Manual—

 

Rev.F_09/13/17 

23 

 

Interferential—

Continuous

 

Premodulated—

Continuous,

 

Surge and Reciprocation

 

Medium Frequency, 

Russian

—

Continuous,

 

Surge and 

Reciprocation

 

Biphasic—

Continuous,

 

Surge and Reciprocation

 

High Volt—

Continuous and Surge

 

Microcurrent—

Continuous 

 

1 0   1 0

min              s

s

s

Hz

 

Surge Mode—

Press Surge selector until you see the On/Off duty cycle that 
you would like to use. Press the

 key to accept the values. 

Preset On/Off choices are 10  10, 10  20, 10  30, 10  40,  
10  50 and 10  60.  
If you press the Surge selector one more time after “10  60” is 
displayed, a single number is displayed. This represents the 
last On time that was programmed. To change the number, 
use the numeric keypad to enter a new value followed by the 

 key. The Off time is then displayed, enter a new value 

followed by the 

 key. 

 

           1 0

min              s

s

s

Hz

 

Reciprocation Mode—

To setup a Reciprocation program you must have stimulation 
setup for two-channel operation. If Channel 1 is lit, press 
Channel 2. If Channel 3 is lit, press Channel 4. 
Press the Reciprocation key. Enter a value from 2 to 240 and 
press the 

 key. 

 

Surge + Reciprocation—

Press Reciprocation key. Press the 

 key. Press the Surge 

key until you see the On/Off time you want to use. Press the 

 key. 

1 5. 0 0

min              s

s

s

Hz

1

2 3

4 5 6
7 8 9

0

 

6.

 

Enter the treatment time using the numeric keypad. The 
maximum treatment time is 60 minutes. If you do not enter a 
time, the time will count up during a treatment session, but 
will not exceed 60 minutes. 

 

7.

 

Apply the electrodes to the patient. Attach the electrode 
cables to the electrodes. 
 
 
 
 
 
 

Summary of Contents for Sys*Stim 294













































Reviews:

No comments

Brands by name

Popular brands

Load more brands