Metra Electronics 99-7397B Installation Instructions Manual Download Page 11 | Manualshive

Page: 11 / 12

background image

REV. 11/11/2020 INST99-7397B

11

TROUBLESHOOTING

For troubleshooting and customization of the steering wheel controls,
visit AXXESSINTERFACES.COM. The Axxess Updater App can also be used.

- Changing radio type
- Remapping the steering wheel control buttons
- Dual assignment instructions (long button press)

Continue to Final Assembly

FINAL ASSEMBLY

1.

Secure the radio assembly to the dash using the factory screws.

2.

Reassemble the dash in reverse order of disassembly to complete the installation.

«
...
9
10
11
12
»

Summary of Contents for 99-7397B













Reviews:

No comments

Related manuals for 99-7397B

Brand: MAC Audio Pages: 20

Brand: RADICAL Pages: 11

Brand: dikom Pages: 21

Brand: FUTABA Pages: 22

Brand: WHD Pages: 4

Brand: SanDisk Pages: 17

Brand: Radio Shack Pages: 24

Brand: Rosen Pages: 28

Brand: Boston Pages: 48

Brand: Pyle Pages: 18

Brand: FTE Pages: 25

Brand: DoorKing Pages: 3

Brand: TURBO RACING Pages: 4

LBT-PAR02 Series

Brand: Elecom Pages: 2

Brand: AFi Pages: 4

Brand: Pyle Pages: 4

Brand: VDO Pages: 2

Brand: Hammarlund Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands