manualshive.com logo in svg

Metos PROVENO E, Installation And Operation Manual

Share
Download
Metos PROVENO E Installation And Operation Manual Download Page 51

| 

51

PROVENO E

Rev. 1.2 (24.08.2016)

Installation

5.2.5.  Surface installation frame fi xed to the fl oor

Surface frames are mounted according to the installation drawing, with the help of distance guides supp-
lied with the delivery. If the inclination of the fl oor is very steep, it may be necessary to level the surface 
frame closer to the horizontal by placing stainless steel spacers between the frame and the fl oor. This 
will ensure that the adjustment range of the pillars is adequate.

Pieces of stainless steel plate should be used as spacers that are large enough and have a suitable hole 
for the fi xing bolt. Washers or other small spacers are not allowed.

The fi xing bolts for the surface installation must be chosen according to the fl oor construction. A type 
recommended is a UKA M10x150 chemical bolt, which suits various fl oor materials. The junction of the 
surface frame and the fl oor is fi lled with fl ooring material or silicone mastic. To achieve the best result 
regarding tightness, the installation frame should be fi lled up to the top level e.g. with acrylic fi ller after 
the installation. The main points concerning the installation of the surface frame are shown in the picture 
below. 

1. Surface frame

2. Concrete casting

3.  Fixing bolt for surface frame

4. Finished fl oor surface

5. Silicone mastic

6. Acrylic fi ller

Fixing bolts of the surface installation must be chosen according to the fl oor material. Recommended 
type is a UKA 12x200 chemical bolt, which is suitable for different fl oor materials. Alternatively expansi-
on-shell bolts or equivalent can be used.

Place the kettle on the surface installation frame and adjust to a horizontal position with 4 adjusting bolts 
which are in the corners of the pillars. When the kettle is in a horizontal position it must be fi xed to the 
surface frame with the help of M12 fi xing bolts. The control pillar has 4 bolts and the support pillar has 
2 bolts. Tighten the fi xing nuts carefully. Do not seal the space between the kettle pillars and surface 
installation frames, as there must be enough change of air.

Summary of Contents for PROVENO E









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands