manualshive.com logo in svg

Metos PROVENO E, Installation And Operation Manual

Share
Download
Metos PROVENO E Installation And Operation Manual Download Page 39

| 

39

PROVENO E

Rev. 1.2 (24.08.2016)

Operation instructions

Power failure during both the starting time and operation time

In case of power failure during both the starting time and operation time, the kettle’s timer display shows, 
when the power supply is restored, the total time the timing was delayed:
•  during operation time, letter E + total delayed time in hours and minutes and the remaining operation 

time alternate on the display, e.g. E1.22 / r0.27, and the green indicator light on the operation time 
button is blinking

•  after operation time, the display shows letter E + total delayed time in hours and minutes, e.g. E1.22, 

and the green indicator light on the operation time button is blinking

•  in case of several power failures, their durations are summed up

After a power failure the kettle must be switched off and on again with the ON/OFF button in order to 
reset the power failure counters.

4.2.16. Programming lockup reset

In the eventual case that wrong EasyRun 1.1 or 99.9 programming locks up the kettle display and turning 
the kettle off and on doesn’t release the lockup there is a reset startup sequence that resets incorrect 
programming parameters and releases the lockup situation.

The reset is done in the following way,
•  turn the kettle off

• 

 push the central dial and keep it pushed

•  turn the kettle on

•  the temperature display shows the fi rmware revision of the kettle and all the button leds are on

•  while the central dial is pushed push the 

  –button and keep it pushed until the display shows 

‘Er1’ and the button led fl ashes

•  keep both the central dial and the button pushed until the ‘Er1’ message disappears and the button 

led goes off

•  turn the kettle off and on again

•  now the lockup is reset

Summary of Contents for PROVENO E









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands