METIEC MT1100 Operation And Installation Manual Download Page 19

 

 
 

 

A1-MT1100 

18 

 

Specific Absorption Rate (SAR) information: 

This product meets the government's requirements for exposure to radio waves. The guidelines are based on 

standards that were developed by independent scientific organizations through periodic and thorough 

evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety 

of all persons regardless of age or health. 

FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one 

gram  of  tissue.  This  device  was  tested  for  typical  body-worn  operations  with  the  back  of  the  handset  kept 

10mm  from  the  body.  To  maintain  compliance  with  FCC  RF  exposure  requirements,  use  accessories  that 

maintain  a  10mm  separation  distance  between  the  user's  body  and  the  back  of  the  handset.  The  use of  belt 

clips,  holsters  and  similar  accessories  should  not  contain  metallic  components  in  its  assembly.  The  use  of 

accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and 

should be avoided. 

Body-worn Operation 

This  device  was  tested  for  typical  body-worn  operations.  To  comply  with  RF  exposure  requirements,  a 

minimum separation distance of 10mm for body worn must be maintained between the user’s body, including 

the  antenna.  Third-party  belt-clips,  holsters,  and  similar  accessories  used  by  this  device  should  not  contain 

any  metallic components. Body-worn accessories that do not meet these requirements may not comply with 

RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. 

 

 

 

 

 

 

Summary of Contents for MT1100





















Reviews: