Configuration & Calibration
31
3.10 Set D/A Trim
D/A Trim is NOT a calibration! This is a pre
calibrated alignment to precision factory settings
and is rarely in need of change. The procedure is
intended only as a slight "meter" adjustment to a
known external reference.
The Digital to Analog (D/A) Trim adjusts the transmitter
mA (current) output. Since the smart transmitter
performs a digital to analog conversion, there may be a
discrepancy in the 4-20 mA output loop as measured with
a reliable external milliampere meter.
For example: perhaps after calibration you observe that
the tank is empty and a hand-held mA meter reads only
3.94 mA, while the Real Time View in the PC Menu shows
4.00 mA. By adjusting the D/A trim, you may digitally
manipulate the output current to equal 4.00. You may
also wish to adjust the high end to 20.00 mA.
To make these adjustments, click on
D/A Trim
on the PC
software Menu Screen and follow the pop-up window
instructions:
3.11 Strapping Table
The strapping table is a 2-point to 21-point table
used by the RCT Series to cause the output current to
follow a specified relationship to the level. There are
certain strapping tables that are already built in to
the transmitter software. These are: Linear (vertical
tank); Horizontal Tank with flat ends; Horizontal Tank
with dished ends; Horizontal Tank with hemispherical
ends; and Spherical Tank. These predefined tables are
automatically created by selections made with Vessel
Configuration assignments during Configuration
procedure in Section 3.7.2, and viewed by clicking the
Strapping Table
"button" on the Main menu.
If the output-to-level relationship is not defined by one
of these tables, you may create a table in the Strapping
Table program. To create a non-linear relationship, you
will need at least 3 points and may use as many as 21
points. A 21-point table will define the relationship with
more accuracy. A common example for a simple table
would be a Cone Bottom Vertical tank which would
require 3 points—the bottom, straight-side break point,
and the top. On the other hand, an open channel flow
application could benefit from using all 21 available
points.
Figure 3-14
Setting D/A Trim Menu Screen
"Pop-Ups"
Summary of Contents for RCT 10 series
