background image

INITIALISE SIM  393

Installer    OK

Select function :

Initialize SIM ?

Function active 

Please wait

Done

Installer    OK

Select function:

Battery Check  ?

Int 7,2V +22°C

Ext 14,3V ok [OK]

Done

This step is very important!

This step is necessary the first time the product is switched on after the

SIM card has been inserted or if it has been replaced at a later date. This
function must be launched in order to download data onto the SIM card
itself.

When this is done, reconfiguration is also required for all the calls lists,

as they will have been deleted..

Always use SIM cards whose phonebook is empty; otherwise, its first

twenty positions will be deleted as these are used by the device for its

operating data.

MetaSystem recommends the exclusive use of contract-based SIM

CARDS.

This menu displays the status of the batteries: the device’s own internal

emergency battery, and the external battery of the vehicle.

If the voltages are within the limits set by the software, a small  “

ok

sign will appear next to the reading for the external battery.

If the battery is disconnected, a small  “

off

” sign will appear next to the

reading for the external battery.

If the battery drops below the acceptable level, a small  “

nok

” sign will

appear next to the reading for the external battery.

CHECK BATTERIES  370

OK

OK

OK

Installer    OK

Select function:

Check 

GPS Status ?

_ _ _ _ _   4sv

4  current fix  105

Done

OK

OK

CHECK GPS STATUS  366

Only use this menu if a GPS module is present 

(only for GPA800)

This menu shows how many satellites are visible at that time in a

numerical and chart format.
Explanation of descriptions:

_ _ _ _ _   = Portrayal in chart format of the number and intensity

of satellites.

4sv

= This means 

4 s

atellites are 

v

isible

4

= Data not for consumer use!

current fix

= This means the GPS fix is taking place correctly

105

= Numerical counter (not for consumer use!)

Other messages possible:

previous fix

= This means this is not a current GPS fix. Wait for a new

fix to be established.

fix not avail.

= This means a GPS fix has never been established. Wait

for a fix to be established.

GPS OFF

= This means the GPS is in low consumption mode. The

ignition key is probably switched off.

NO GPS

= this means the GPS has not been located. Possible causes:

Incorrect connections or GPS failure.

NB: Always take the vehicle outside for testing; should you encounter

problems, check the connections of the aerial and the cabling. Should the
problems persist, try installing the aerial elsewhere.

8

Summary of Contents for GPA600





















Reviews: