manualshive.com logo in svg

Meta System GPA600, Installation And Programming Manual

The Meta System GPA600 product offers advanced features for installation and programming. Gain comprehensive insight with the free Installation and Programming Manual available for download at manualshive.com. Explore detailed instructions and optimize your experience by accessing the manual today.

Share
Download
background image

HIDDEN MENUS CALLED UP BY QUICK COMMANDS

The menus shown below can only be called up by using the quick commands. These menus are not usually displayed
because they should not be needed for standard installation purposes. They are, therefore, “hidden“ and can be called up
should this be necessary. In order to display them, enter INSTALLER Level, enter the relevant quick command and press OK.
The menu will be concealed once again after you have exited it.

This is the serial number of the internal GSM module. 
It always differs from product to product (the number shown
opposite is by way of example!)

This is the version of the internal GSM module’s software.
This menu is used to verify its update status.

(the number shown opposite is by way of example!)

If you press OK, you can ask the device to provide
information concerning the remaining credit in the credit for
unit SIM card.

This menu is used to modify the number of units for the
transmission of the low credit warning message, placed by
the LOW CREDIT calls list. It is possible to set a minimum of
10 units and a maximum of 1000 units.

This menu is used for the configuration of the format for the
display of the GPS coordinates. In addition to
DEGREE.MIN.SEC, it is possible to set DECIMAL or NMEA
formats. Use the 

+

and 

–

keys to select the format and the

OK

key to confirm the modification or the 

C

key to exit

without storing it.

This menu is used to modify the filter for the ignition key
signal. This parameter makes it possible to compensate for
any disturbance on the signal. It is possible to programme
from 0 to 254 units and each unit corresponds to 16ms. A
higher number corresponds to a greater filter. 

This menu is used to modify the filter for the alarm VOL1
signal. This parameter makes it possible to compensate for
any disturbance on the signal. It is possible to programme
from 0 to 254 units and each unit corresponds to 16ms. A
higher number corresponds to a greater filter.

This menu is used to modify how much time must pass
before the ignition will be immobilised by means of a remote
command via SMS after the ignition key has been switched
off. The default factory setting is 15 sec, but it can be
programmed from 0 to 60 sec.

208

209

371

384

502

503

424

367

DISPLAY

WHAT IT MEANS

QUICK

COMMAND

16

IMEI Code

520338422519442

GSM mode SW Rel.

REVISION 04.00

Check

GSM credit?

Credit warning 

at 50 units 

co-ordinate mode:

DEGREE.MIN.SEC

Anticarjack:

KeyLock  15sec

Stimuli filter

value       10

VOL1     filter

value       10

Summary of Contents for GPA600





















Reviews:

No comments

Related manuals for GPA600

unication G4 Quick Manual preview
G4
Brand: unication Pages: 2

Brands by name

Popular brands

Load more brands