background image

G815

D

 May 05

22

no change, Step 12 selects the ‘stop when interrupted, move when clear’ option:
11.  

Only press P1/SET to close the gates if:
a. photocell is obstructed when closing then reverse immediately, and;
b. photocell is obstructed when opening do nothing

12.  

Only press P2/RADIO to close the gates if:
a. photocell is obstructed when closing then stop and only reverse when obstruction 
is removed, and;
b.  photocell  is  obstructed  when  opening  then  stop  and  continue  opening  when 
obstruction is removed

13.  

The two leaves will close fully, slowing down at the time previously chosen

The following steps are for pedestrian access only:
14.  

Only  press  P1/SET  if  Pedestrian  Access  is  required.  The  M1  leaf  will  begin 
opening.

Press  P1/SET  at  the  time  where  the  Pedestrian  Access  wing  is  at  the  desired  open 

position. The leaf will close fully and the unit will exit Professional Setup.

15.  

If  Pedestrian  Access  is  not  required,  press  P1/SET  and  P2/RADIO 
simultaneously

NOTE

  The professional setup procedure will time out after four minutes if abandoned.

Testing the gate operation

Test the operation of all controls and safety devices.
Allow for the effect of weather. Wind or water will make the gates more difficult to move. If 
the sensitivity is set to react to extremely light obstructions then the gates may fail to open 
or close fully. After adjustment, check that the force on an obstruction at the far end of the 
gate leaf does not exceed 150N (15 kg). Use a spring balance.

Summary of Contents for G815D





























Reviews: