Mercusys MW302R User Manual Download Page 96

Page: 96 / 143

Chapter 7

• Username/Password

- Enter the username and password provided by your ISP. These

fields are case-sensitive.

• VPN Server IP/ Domain Name

- Enter the VPN server’s IP address or domain name

provided by your ISP.

• MTU Size

- The default MTU size is “1460” bytes, which is usually fine. It is not

recommended that you change the default MTU Size unless required by your ISP.

• Connection Mode

• Auto

- In this mode, the internet connection reconnects automatically any it gets

disconnected.

• On Demand

- In this mode, the internet connection will be terminated automatically

after a specified inactivity period (Max Idle Time) and be re-established when you
attempt to access the internet again.

Summary of Contents for MW302R
















































































































































Search results

Summary of Contents for MW302R

Reviews:

Related manuals for MW302R

Brands by name

Popular brands

Mercusys MW302R, User Manual

Search results

Summary of Contents for MW302R

Reviews:

Related manuals for MW302R

Brands by name

Popular brands