Mercusys MW302R User Manual Download Page 23

Page: 23 / 143

Chapter 4

• Status

- Indicates whether the router has been connected to the internet.

• Internet Connection Type

- Indicates the way in which your router is connected to

the internet.

• IP Address

- The WAN IP address of the router.

• Subnet Mask

- The subnet mask associated with the WAN IP address.

• Default Gateway

- The Gateway currently used is shown here. When you use

Dynamic IP as the internet connection type, click

Renew

Release

here to obtain

new IP parameters dynamically from the ISP or release them.

• Primary & Secondary DNS

- The IP addresses of DNS (Domain Name System)

server.

• LAN

- This field displays the current settings of the LAN, and you can configure them on

the

Advanced

Network

LAN page

• MAC Address

- The physical address of the router.

• IP Address

- The LAN IP address of the router.

• Subnet Mask

- The subnet mask associated with the LAN IP address.

• DHCP Server

- This field displays the current settings of DHCP (Dynamic Host

Configuration Protocol) Server, and you can configure them on the

Network

DHCP

Server

page.

• DHCP Server

- Indicates whether the DHCP server is enabled of disabled. It is

enabled by default and the router acts as a DHCP server.

• IP Address Pool

- The IP address range for the DHCP server to assign IP addresses.

• Dynamic DNS

- This field displays the current settings of the Dynamic DNS (Domain

Name System), and you can configure them on the

Advanced

Network

Dynamic DNS

page.

• Service Provider

- The Dynamic DNS service provider you have signed up for.

• Host Name

- The Domain Name you have entered in the Dynamic DNS page.

• Status

- The status of the Dynamic DNS service connection.

4. 2. 2. Internet

1. Visit

http://mwlogin.net

, and log in with the password you set for the router.

Go to

Advanced

Network

Internet

Set up the internet connection and click

SAVE

Dynamic IP

If your ISP provides the DHCP service, please select

Dynamic IP

, and the router will

automatically get IP parameters from your ISP.
Click

RENEW

to renew the IP parameters from your ISP.

Summary of Contents for MW302R
















































































































































Search results

Summary of Contents for MW302R

Reviews:

Related manuals for MW302R

Brands by name

Popular brands

Mercusys MW302R, User Manual

Search results

Summary of Contents for MW302R

Reviews:

Related manuals for MW302R

Brands by name

Popular brands