manualshive.com logo in svg

MerCruiser Vazer 100, Owner'S Manual

Share
Download
MerCruiser Vazer 100 Owner'S Manual Download Page 98

Section 5 - Maintenance 

Page  90

90-899883182   NOVEMBER  2007

Description

Location

Figure

Front trim cylinder anodes Mounted on the front on each of the trim

cylinders.

26226

Rear trim cylinder anodes

Mounted on the rear on each of the trim

cylinders.

26227

Gearcase anodic plate

Mounted on the underside of the lower

gearcase.

26225

Bearing carrier anode

Located in front of the propeller, between

the front side of the propeller and the gear

housing.

26228

Gimbal housing anode

Mounted on the bottom of the gimbal

housing.

26224

MerCathode Kit

(if equipped)

Mounted to the boat transom on opposite

sides of the sterndrive. The MerCathode

controller is mounted on the engine or on

the inside of the boat transom.

26234

Anode kit (if equipped)

Mounted to the boat transom.

26300

In addition to the corrosion protection devices, take the following steps to inhibit corrosion.
1. Paint the power package. See 

Painting Your Power Package

.

2. Annually spray the power package components on the inside of the boat with Corrosion

Guard to protect the finish from dulling and corrosion. You may also spray external

power package components.

3. Keep all lubrication points, especially the steering system, shift and throttle linkages,

well lubricated.

4. Flush the cooling system periodically, preferably after each use. See 

Flushing Your

Power Package

.

Summary of Contents for Vazer 100























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands