manualshive.com logo in svg

MerCruiser Vazer 100, Owner'S Manual

Share
Download
MerCruiser Vazer 100 Owner'S Manual Download Page 78

Section 5 - Maintenance 

Page  70

90-899883182   NOVEMBER  2007

7. Remove the oil vent screw and sealing washer. Allow the gear lube to drain completely.

26216

a

a -

Oil vent screw

IMPORTANT: If any water drained from the oil fill and drain hole, or if the gear lube appears

milky, the sterndrive is leaking and should be checked immediately by your authorized

Mercury MerCruiser dealer.
8. Lower the sterndrive so that the propeller shaft is level.
9. Fill the sterndrive through the oil fill and drain hole with specified gear lubricant until an

air‑free stream of lubricant flows from oil vent hole.

Tube Ref No.

Description

Where Used

Part No.

87

High Performance Gear

Lubricant

Sterndrive

92-858064K01

IMPORTANT:  Use  only  Mercury/Quicksilver  High  Performance  Gear  Lubricant  in

sterndrive.
10. Install the oil vent screw and sealing washer.
11. Continue to pump gear lubricant into the drive through the oil fill and drain hole until the

gear lubricant appears in the gear lube monitor.

12. Fill the monitor so that the gear lube level is in the operating range. Do not overfill.

Summary of Contents for Vazer 100























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands