manualshive.com logo in svg

MerCruiser Vazer 100, Owner'S Manual

Share
Download
MerCruiser Vazer 100 Owner'S Manual Download Page 58

Section 4 - Specifications 

Page  50

90-899883182   NOVEMBER  2007

Engine Specifications

NOTE: Performance ratings are obtained and corrected in accordance with SAE J1228/

ISO 8665 Crankshaft Power.
NOTE: All measurements are taken with the engine at normal operating temperature.

Models

Vazer 100

Power

75 kW (100 hp)

Number of cylinders

4

Displacement

1.6 L (98 cid)

Bore and stroke

79 × 81.5 mm (3.11 × 3.21 in.)

Compression ratio

9.6:1

Idle RPM in neutral

600

Max RPM at WOT

5600–6000

Minimum oil pressure at idle

127 kPa (18.5 psi)

Thermostat (opening temperature)

82° C (180° F)

Timing

Non‑adjustable

Electrical system

12 V negative ground

Minimum battery requirement

375 CCA / 475 MCA / 90 Ah

Alternator rating

65 A

Firing order

1‑3‑4‑2

Spark plug type

Champion—RN2C

Spark plug gap

0.9 mm ± 0.1 mm (0.035 in. ± 0.004 in.)

Fluid Specifications

Engine

IMPORTANT: All capacities are approximate fluid measures.

Vazer 100 with Emissions Control

Capacity

Fluid Type

Engine oil with filter

4 L  (4.25 US qt) Mercury Full‑Synthetic MerCruiser 20W‑40

Closed cooling system

7.8 L (8.24 US qt)

Mercury Extended Life Coolant Antifreeze or extended

life ethylene glycol 5/100 antifreeze mixed 50/50 with

purified water

Sterndrives

NOTE: Oil capacity includes drive lube monitor.

Model

Capacity

Fluid Type

Vazer Drive

1892 mL (64 oz)

High Performance Gear Lubricant

Power‑Assisted Steering and Power Trim Fluids

APPROVED POWER-ASSISTED STEERING FLUIDS

Description

Part Number

Power Trim and Steering Fluid

92‑858074K01

Dexron III Automatic Transmission Fluid

Obtain locally

Summary of Contents for Vazer 100























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands