manualshive.com logo in svg

MerCruiser Vazer 100, Owner'S Manual

Share
Download
MerCruiser Vazer 100 Owner'S Manual Download Page 47

Section 3 - On The Water

90-899883182   NOVEMBER  2007

Page  39

5. Throttle‑only mode is deactivated by moving the control lever to the neutral position.

Moving the control lever from the neutral position to the forward, idle or reverse, idle

position without pressing the throttle‑only button will shift the power package into the

chosen gear.

Trailering the Boat

Your  boat  can  be  trailered  with  the  sterndrive  in  the  up  or  down  position.  Adequate

clearance is required between the road and the sterndrive when transporting.
If adequate road clearance is a problem, place the sterndrive in the full trailer position and

support  it  with  an  optional  trailer  kit,  which  is  available  from  your  authorized  Mercury

MerCruiser dealer.

Freezing Temperature Operation

IMPORTANT:  If the boat is operated during periods of freezing temperature, precautions

must be taken to prevent freeze damage to the power package.
If operating in freezing or near freezing temperatures, keep the sterndrive trimmed down

(in) at all times so that the sterndrive remains submerged. This prevents trapped water in

the sterndrive from freezing and causing possible damage to the seawater pump and other

sterndrive components.
IMPORTANT: The seawater section of the Vazer 100 is self draining and will drain when

the boat is removed from the water.
If there is a chance of ice forming on the water, remove the boat from the water and allow

the seawater section to drain completely of water. If ice should form at the water level inside

the sterndrive or engine, it will block water flow to the engine causing possible engine and

sterndrive damage.
1. Remove the boat from the water.
IMPORTANT: Place the sterndrive in the full down (in) position to ensure that no seawater

gets trapped in the engine or sterndrive.
2. Place the sterndrive in the full down (in) position.
3. Allow the system to drain for a minimum of 5 minutes before raising the sterndrive.

Drain Plug and Bilge Pump

The engine compartment in your boat is a natural place for water to collect. For this reason,

boats are normally equipped with a drain plug and/or a bilge pump. It is very important to

check these items on a regular basis to ensure that the water level does not come into

contact  with  your  power  package.  Components  on  your  engine  will  be  damaged  if

submerged. Damage caused by submersion is not covered by the Mercury MerCruiser

Limited Warranty.

Protecting People In The Water

WHILE YOU ARE CRUISING

It is very difficult for a person in the water to take quick action to avoid a boat heading in

their direction, even at slow speeds.

21604

Summary of Contents for Vazer 100























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands