background image

P 23

Please retain product label and instructions for future reference

             

IMPORTANT: 

Pre-drill before fixing screws.

Step 40

Parts needed - No. 70 QTY 1    

 

  

Place the floor boards (

No. 70

inside the building flush to the log 

boards on one side. 

Continue  adding the floor boards 

(

internally

) making sure to interlock 

each individual board.

*Do 

NOT

 secure the boards until 

the last board has been measured 

and cut.

Following the same method 

outlined previously measure the 

gap between the bottom of the 

tongue (

on the last  board placed

and the log board.

Using a straight edge mark out the  

measurement onto the last floor 

board (

No. 70

) and cut along the 

length removing the excess.

**Please note:

 Mark the final board 

2mm under the measurement; This 

will allow the timber to expand and 

contract correctly.

Once all the floor boards are in

position secure each board into 

position using 8x40mm screws per 

board.

***Please Note:

 

Ensure to screw  

through each of the floor boards into 

the floor bearers.

200x40mm Screws 

40mm 

screw

Pre drill 

hole

This is for illustrative purposes only and may differ from your floor.

70

70

IMPORTANT: 

Pre-drill before fixing screws.

Roof

Closure Trim

Internal

67

*Measure and cut the

closure trims to

fit the internal space.

Pre drill 

hole

30mm 

screw

*

trim to fit

Step 41

Parts needed - No. 67 QTY 7 

   

 

Inside the building place the closure 

trim (

No. 67

) against the boarding and 

align with the roof as shown in the 

illustration. 

*Measure and cut the closure trims to 

fit the internal space.

Once in position fix each trim  into 

place by pre drilling a pilot hole and 

using 6x30mm screws per trim, 

equally spacing them along the face 

of the board.

42x30mm Screws

IMPORTANT: 

Pre-drill before fixing screws.

*Internal view

67

67

30mm 

screw

Pre drill 

hole

*

Cut to fit

Step 42

Parts needed - No. 67 QTY 7

Once the floor has been laid arrange the

closure trim (

No. 67

) around the outside 

edge of floor (

internally

), measure and cut 

down accordingly to best match the 

internal space.

Secure each trim section into place using 

6x30mm spaced equally along the board 

as shown in the illustration.

*Do NOT fix the closure trim to the floor

boards.

42x30mm Screws

 

Summary of Contents for 0634CSNE0303HGDD2SW-V1


























Reviews: