background image

P 11

Please retain product label and instructions for future reference

             

Pre drill 

hole

70mm 

screw

23

23

Step 16

Parts Needed - No. 23 QTY 2

Once the gables are in position 

place the Finisher Boards (

No. 23

onto the front and rear of the 

building, fixing into position by 

screwing through the notches as 

shown in the illustration. 

*Ensure that the boards are level 

and flush with each other as you 

lay each one.

4x70mm Screws 

Rubber Mallet 

may be required 

to fit parts.

IMPORTANT : 

Pre-drill before fixing screws.

26

26

a

IMPORTANT: 

Pre-drill before fixing screws.

26

26

Pre drill 

hole

70mm 

screw

Step 17

Parts needed - No. 26 QTY 3

 

Align the Roof Purlin(

s

(

No.26

) into the cut out slots on each 

gable top ensuring each roof purlin 

interlocks the boards.

 

Secure the roof purlins at 

each end by screwing through the 

bars into the boards (

ensure to 

pre-drill to avoid the boards 

splitting

) using 4x70mm screws per 

roof purlins.

*Please note:

 The gable shown is for  

illustrative purposes and may differ in 

width from your choice in product. 

Nevertheless, despite any differences 

the process of fixing the roof purlins is 

the same.

12x70mm Screws

a

b

Rubber Mallet 

may be required 

to fit parts.

26

b

Summary of Contents for 0619RANE3503FGSD3TW-V1


















Reviews: