1-833-454-0864
1 0
Lighting Burners
1. Turn all burner control knobs
“OFF”
. (Push in and turn the knobs clockwise to confirm
“OFF”
position.)
2.
Open LP tank
SLOWLY
. Turn counter clockwise to open. Wait 5 seconds for pressure to stabilize.
3. Push-in control knob to start gas flowing, then turn control knob counter-clockwise to
“HI”
position to activate
starter.
4. Check that the burner is lit. Repeat STEP 3 if necessary.
5. Repeat step 3 for all remaining control knobs
6. Check that all burners are lit.
If the burners fail to light properly within 3-5 seconds, turn the burner control knob
“OFF”
. Also turn off the LP cylinder
valve. Wait five minutes before attempting to light the burner again. This will allow time for released gas to dissipate.
LIGHTING INSTRUCTIONS
WARNING
Never stand with your head directly over the griddle when preparing to light the main burners, to prevent possible
bodily injury.
WARNING
Before you light this griddle, turn all control knobs to the “
OFF
” position and close the LP Cyclinder.
Failure to follow proper lighting sequence will activate the regulators “
FLOW LIMITING DEVICE
” feature,
and require a reset (See page 8).
OFF
HI
LOW
OFF
HI
LOW
OFF
HI
LOW
OFF
HI
LOW
Lighting Instructions
1. Read instructions before lighting.
2. Make sure all control knobs are in the "OFF" position.
3. Turn ON gas valve from LP tank.
4. The IGNITION BURNERS are the middle two control knobs.
Light them first. Press and turn them slowly to "HI".
5. If ignition does NOT occur in 5 seconds, turn the
burner controls off, wait 5 minutes, and repeat
the lighting procecure.
6. Once the IGNITION BURNERS are lit, you
may light other burners.
Just press and turn the control knob to "HI".
7. To turn burners off, turn the control knobs
clockwise until they lock in the "OFF"
position.
IGNITION
BURNER
IGNITION
BURNER
Lighting Instructions
1. Read instructions before lighting.
2. Make sure all control knobs are in the "OFF" position.
3. Turn ON gas valve from LP tank.
4. The IGNITION BURNERS are the middle two control knobs.
Light them first. Press and turn them slowly to "HI".
5. If ignition does NOT occur in 5 seconds, turn the
burner controls off, wait 5 minutes, and repeat
the lighting procecure.
6. Once the IGNITION BURNERS are lit, you
may light other burners.
Just press and turn the control knob to "HI".
7. To turn burners off, turn the control knobs
clockwise until they lock in the "OFF"
position.
IGNITION
BURNER
IGNITION
BURNER
OFF
HI
LOW
OFF
HI
LOW
OFF
HI
LOW
OFF
HI
LOW
Summary of Contents for G70201
