Page | 1
BACnet Protocol Implementation Conformance Statement .......................................... 2
Object/Property Support Matrix ................................................................................................. 4
Device Object Description ............................................................................................................. 5
System Controller ................................................................................................................................................ 5
Exhaust Fans and Auxiliary Airflows ......................................................................................................... 10
Hood Controllers ............................................................................................................................................... 12
Virtual Input Module ....................................................................................................................................... 12
Virtual Output Module ................................................................................................................................... 13
Getting Started: Pre-Installation Checklist .......................................................................... 14
Configuring the Intelli-Hood System ...................................................................................... 16
Configuration through the Touchpad ....................................................................................................... 16
Configuration through the Web-Based Configuration ..................................................................... 17
Configuration through a USB Flash Drive .............................................................................................. 18
Networking Setup and Configuration .................................................................................... 19
BACnet Setup and Configuration ............................................................................................. 20
Common BACnet Interfacing Use Cases ............................................................................... 22
Monitoring Fan Speeds ................................................................................................................................... 22
Monitoring Energy Consumption ............................................................................................................... 22
Setting Time on the Intelli-Hood system ................................................................................................. 23
Appendix A: Device List and Device Instance Numbering ............................................. 24
Device Object MAC Address ........................................................................................................................ 25
Example Scenarios ............................................................................................................................................ 25
Manual Device Instance Numbering ......................................................................................................... 28
Verifying BACnet Device Instance Numbers ........................................................................................ 29
Appendix B: Troubleshooting Guide ....................................................................................... 31
Cannot detect any Intelli-Hood Device Objects .................................................................................. 31
Can only detect the System Controller Device Object ..................................................................... 31
Cannot set the Intelli-Hood system time ................................................................................................ 32
Virtual Input Module digital inputs and analog inputs keep resetting ....................................... 34
