Meinberg GPS164-LQ/PPFO-3/REL-1/DAHS Manual Download Page 3

Page: 3 / 46

Table of Contents

General Details

Safety Hints

2.1 Content of the USB stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Frontpanel

General information about GPS164

Block diagram GPS164xhs

GPS164 Features

6.1 Time Zone and Daylight Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2 Pulse outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.3 Asynchronous Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6.4 Time code outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6.4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6.4.2 Generated Time Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6.4.3 Code generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6.4.4 IRIG Standard Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

6.4.5 AFNOR Standard Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

6.4.6 Assignment of CF Segment in IEEE1344 Code . . . . . . . . . . . . . . . . . . . . . . . . 14

Installation

7.1 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

7.2 Assignment of the DSUB connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

7.3 BNC connector GPS Ant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

7.4 Error Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

7.5 Mounting the GPS Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

7.5.1 Assembly of the GPS antenna surge protector . . . . . . . . . . . . . . . . . . . . . . . . 18

7.6 Powering Up the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

7.7 Change the Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

The Front Panel Layout

8.1 FAIL LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

8.2 LOCK LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

8.3 OCx LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

8.4 BSL Key (hidden) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Technical Specifications GPS164DAHS

9.1 Technical Specications GPS Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

9.2 Time Strings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

9.2.1 Format of the Meinberg Standard Time String . . . . . . . . . . . . . . . . . . . . . . . . 25

9.2.2 Format of the Meinberg GPS Time String . . . . . . . . . . . . . . . . . . . . . . . . . . 26

9.2.3 Format of the Meinberg Capture String . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

9.2.4 Format of the SAT Time String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

9.2.5 Format of the Uni Erlangen String (NTP) . . . . . . . . . . . . . . . . . . . . . . . . . . 29

9.2.6 Format of the NMEA 0183 String (RMC) . . . . . . . . . . . . . . . . . . . . . . . . . . 31

9.2.7 Format of the NMEA 0183 String (GGA) . . . . . . . . . . . . . . . . . . . . . . . . . . 32

9.2.8 Format of the NMEA 0183 String (ZDA) . . . . . . . . . . . . . . . . . . . . . . . . . . 33

9.2.9 Format of the ABB SPA Time String . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

9.2.10 Format of the Computime Time String . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

9.2.11 Format of the RACAL standard Time String . . . . . . . . . . . . . . . . . . . . . . . . . 36

9.2.12 Format of the SYSPLEX-1 Time String . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Summary of Contents for GPS164-LQ/PPFO-3/REL-1/DAHS















































Search results

Summary of Contents for GPS164-LQ/PPFO-3/REL-1/DAHS

Reviews:

Meinberg GPS164-LQ/PPFO-3/REL-1/DAHS, Manual, Page: 3 / 46

Search results

Summary of Contents for GPS164-LQ/PPFO-3/REL-1/DAHS

Reviews: