manualshive.com logo in svg

Meinberg GPS164-LQ/PPFO-3/REL-1/DAHS, Manual, Page: 21 / 46

Share
Download
Meinberg GPS164-LQ/PPFO-3/REL-1/DAHS Manual Download Page 21

7.3 BNC connector GPS Ant

Page 17

7.3 BNC connector GPS Ant

The antenna/converter unit is connected to the receiver circuit of the GPS164 through this connector.

7.4 Error Relay

On the front panel of the device you can nd a DFK connector labeled "Error". This is a potential free contact

which is directly controlled by the reference clock. Normally, when the reference clock is synchronized, the relay

and the relay contact NO is active. If the reception is diturbed or the device even turned o, the NC relay contact

is activated.

NO
NC
CO

Error

Technical Specication

Switching voltage/current AC

(resistive load):

max. 250 V, 1 A

Switching voltage/current DC

(resistive load):

max. 230 V, 0.1 A

max. 30 V, 1 A

Response time:

10 ms

Isolation coil/contact:

4 kV

Error Mode

CO NC NO

   Error:

 

CO - NC   connected

Normal Operation Mode

CO NC NO

Normal Operation:    

 CO - NO   connected

WARNING:  DANGER TO LIFE BY ELECTRICAL SHOCK!

NO LIVE WORKING !
Terminals of the error relay may be energized at dangerous voltage levels! 
Do not carry out electrical works when terminals or signalling lines are 
energized! All connectors must be equipped with suitable covers to prevent 
from electrical shock or hazard!

GPS164

Date: 27th January 2016

17

Summary of Contents for GPS164-LQ/PPFO-3/REL-1/DAHS















































Reviews:

No comments