manualshive.com logo in svg

Meinberg GPS164-LQ/PPFO-3/REL-1/DAHS, Manual, Page: 20 / 46

Share
Download
Meinberg GPS164-LQ/PPFO-3/REL-1/DAHS Manual Download Page 20

Page 16

7 Installation

7.1 Power supply

Supply voltage and protective earth must be applied to the device via the 5-pole connector `Power'. The supply

line used for this device must be equipped with an appropriate switch that must be mounted close to the device

and must be marked as a mains switch for the device. Furthermore, to ensure safe operation supply mains con-

nected to this device must be equipped with a fuse and a fault-current circuit breaker according to the applicable

national standards. The device must be connected to a protective earth with low grounding resistance according

to the applicable national rules.

max. 25 VA

100 V to 240 V

100 V to 240 V

max. 8 W

47 Hz to 63 Hz

Supply

Input voltage

Power consumption

Frequency

WARNING:  DANGER TO LIFE BY ELECTRICAL SHOCK!

NO LIVE WORKING !
Terminals of the power connector are energized at dangerous voltage levels! 
Do not carry out electrical works when terminals or cables are energized! 
All connectors must be equipped with suitable covers to prevent from electrical 
shock or hazard!

7.2 Assignment of the DSUB connectors

The serial ports COM0 and COM1 are accessible via nine-pole DSUB connectors in the frontpanel. These RS-232

interfaces can be connected to a computer by using a standard modem cable. TxD describes the sending, RxD

the receiving line of the GPS164xHS.

1

6

5

9

RS-232

COM 0 / COM 1

TxD

RxD

GND

WARNING:  DANGER TO LIFE BY ELECTRICAL SHOCK!

NO LIVE WORKING !
Disconnect both sides of the serial port cable before working on its connectors. 
This device is equipped with two galvanically isolated serial ports. Hazardous 
voltages may be applied to the serial cable if a connected device is faulty. 
All connectors must be equipped with suitable covers to prevent from electrical 
shock or hazard!

16

Date: 27th January 2016

GPS164

Summary of Contents for GPS164-LQ/PPFO-3/REL-1/DAHS















































Reviews:

No comments