Meiko K-Tronic Operating Instructions Manual Download Page 39

Page: 39 / 44

Operating instructions dishwashing machine model

K-Tronic

Datei:BA-K-tronic_MIKE_9626212_EN_2005-12-01.doc

9626212

39/44

W e reserv e the right to change execution and construction !

MEIKO Maschinenbau GmbH & Co. KG, Englerstraße 3, D-77652 Offenburg, Tel.: +49/781/203-0, Fax: +49/781/203-1121

Service step









Maintenance

Cleaning works

Daily

At least once

quarterly

At least once

or twice a

year

but

every

1000 h

At least once

yearly

but

every

2000 h

VERY IMPORTANT:

Whenever any electrical components are disconnected and
reconnected, replaced or repaired, a safety test must be
conducted, at least on these components!!!

8. Drying

Fan

Check fan for exterior damage



Check current consumption

(

see wiring diagram)



Check fan for quiet running (bearing damage) (visual and noise check)



Check suction side grid for cleanliness



Damper register (steam or hot water)

Check damper register for cleanliness



Clean damper register with hot water



Check damper register for watertightness (heating medium)



Blowing box

Check fan system nozzles for damage



Function check

The suction side temperature must not exceed

°C.



Check internal drying chamber for cleanliness



Clean internal drying chamber with hot water (remove greases and oils)



see later

9. Heat recovery

Exhaust fan

Check fan for exterior damage



Check current consumption

(

see wiring diagram)



Check fan for bearing noise (damage to bearing)



Check protection grid for cleanliness



Heat exchanger

Check heat exchanger for cleanliness



Clean heat exchanger with hot water



Check heat exchanger watertightness



Summary of Contents for K-Tronic













































Search results

Summary of Contents for K-Tronic

Reviews:

Related manuals for K-Tronic

Brands by name

Popular brands

Meiko K-Tronic, Operating Instructions Manual

Search results

Summary of Contents for K-Tronic

Reviews:

Related manuals for K-Tronic

Brands by name

Popular brands