manualshive.com logo in svg

Megger DELTA4000, Instruction Manual, Page: 49 / 74

Share
Download
Megger DELTA4000 Instruction Manual Download Page 49

 

 
AVTMDELTA4000-EN Rev 6 April 2018 

41 

7  

PowerDB User Interface 

Introduction 

PowerDB Lite is included in your purchase of the DELTA4000. PowerDB Lite 

helps perform testing in an asset based method, and presents results in a 

professional looking data form. Completed data forms are saved as files to your 
computer. 

The DELTA4310A has PowerDB Lite preloaded on the built-in industrial 

controller. DELTA4310A is designed to make testing more intuitive for end 

users, and so restricts the use of the built-in controller to PowerDB functions. 
The presentation and testing methods within the built-in controller are identical 

to the PowerDB Lite PC version. No difference in operation exists, except when 

upgrades between the PC and the DELTA4310A are not maintained by the user. 

Upgrading the DELTA4310A is different than upgrading a PC. Please refer to 
Megger website similar to: http://us.megger.com/my-account/software-

downloads/for latest 'On Board' download software and instructions. 

Minimum Recommended System 

Operating System: 

Windows 7 or later 

RAM 

2GB RAM minimum, 
>4GB RAM recommended 

>2G free memory space 

Processor:

 

2.0G Hz Pentium Class processor 
minimum, 

For more information please visit 

www.powerdb.com

 or contact your local sales 

representative. 

 

 

 

Summary of Contents for DELTA4000











































































Reviews:

No comments