manualshive.com logo in svg

Megger DELTA4000, Instruction Manual, Page: 27 / 74

Share
Download
Megger DELTA4000 Instruction Manual Download Page 27

Controls, Indicators, and Connectors 

 

 

AVTMDELTA4000-EN Rev 6 April 2018 

19 

DELTA4310A Top Panel Features 

 

Figure 3: Optional Industrial 12 inch Controller 

The optional industrial 12 inch controller is:  

1.

 

Industrial 300 mm (12 inch) Touch Display:

 Used in place of a PC. 

Designed to run PowerDB Lite with focus on selected Megger 

instrument control related to transformer testing. When turned on, 

defaults to DELTA4000 transformer forms. 

2.

 

Built-in Printer: 

Designed to print individual results and is active within 

specific forms via 'print icon' located within selected forms. 

3.

 

USB Port:

 Used for various functions including external memory and 

external mouse/keyboard control. 

 

4.

 

Rear USB Port Hub:

 Used for external Megger instrument control such 

as TTR300, TTR310E, S1/MIT Insulation test set, MLR10.  

5.

 

Rear Ethernet Port

: Used for external Megger instrument control – 

specifically the MTO300, TTR310E, MTO250. 

The DELTA4310A 300 mm (12 inch) display is meant to replace a customer PC with an 

industrial controller designed to work in harsh environments. This built-in display features 

protection against accidental shut down of the instrument by safely turning off Windows 

operating system together with PowerDB after shutdown (switch is turned off) is detected. 
This safe shutdown prevents damage to the internal memory, and to the software 

operating system. 

Summary of Contents for DELTA4000











































































Reviews:

No comments