manualshive.com logo in svg

Megger DELTA4000, Instruction Manual, Page: 32 / 74

Share
Download
Megger DELTA4000 Instruction Manual Download Page 32

M 
 

 

AVTMDELTA4000-EN Rev 6 April 2018 

24 

 

Figure 5: Typical Test Setup for Transformer Excitation Current Measurements 

1.

 

Locate the test set at least 6 ft (1.8 m) from the specimen to be tested. 

2.

 

Connect the test ground to a low impedance earth ground on the 
specimen (if possible). This should always be the first cable connected 

and last removed 

3.

 

Connect the control and power cables between the control and HV units. 

Make sure that the bayonet type plugs are fully locked on the receptacles. 

4.

 

Connect the measurement cable with the red colored boot to the INPUT 

RED receptacle. Make sure the connector locks to the receptacle. If 

required, connect the measurement cable with the blue colored boot to 

the INPUT BLUE receptacle. 

5.

 

Connect the external interlock cables or a test area interlock system to 

the INTERLOCK 1 and 2 receptacles. Make sure the plugs are fully 

seated and locked on the receptacles. 

6.

 

Connect the high-voltage cable to the high-voltage terminal of the high-
voltage unit (be sure that the connector locks in place).  

DELTA4000 

CONTROL  UNIT 

DELTA4000 

HIGH 

VOLTAGE 

UNIT 

Summary of Contents for DELTA4000











































































Reviews:

No comments