background image

 

as much effort and for as long as possible (minimum 1.5 seconds). If no 
inhalation has occurred the alarm will constantly make an audible beep 
indicating it is waiting for a test to be performed, when inhalation starts a 
longer audible beep will be heard. 
 
The display will show maximum average inspiratory pressure sustained 
over a one second period of the test - MIP. If the manoeuvre was less than 
1.5 seconds, the unit will beep and a stopwatch with an exclamation mark 
will be displayed indicating that the expiration needs to be longer. When 2 
seconds exhalation has occurred, an audible noise will be made indicating 
the acceptable time period has been met. After each manoeuvre has been 
performed pressing the select key 

  momentarily will allow the operator to 

view the Pressure time trace and the additional indices PMax, PAv, MRPD, 
and MRR.  
 
Pressing the select key and keeping it held down will change the display 
back to the MIP blow icon. 
  
It is recommended to perform three good tests and use the best result as 
the maximum achievable MIP, MEP or SNIP. The ATS recommends for 
reproducibility that the three tests performed should be within 20% of the 
highest MIP pressure obtained. As tests are performed the highest value 
acceptable test (over 1.5 seconds) will be displayed along with a cup to 
indicate the best test, if subsequent tests are within 20% they will be shown 
with a smiley face and if not within the 20% reproducibility a sad face will be 
displayed, indicating further testing should be performed. 
 

NOTE:

 Once three acceptable tests have been performed a flag will be 

shown at the top of the display to indicate the reproducibility criteria has 
been met. 
 
 
 

  The maximum reading the RP

 

Check can measure is equivalent to 

300 cmH

2

O. Any reading above that will be displayed as --- 

(overflow). 

 

NOTE:

 If the patient does not inhale for the minimum period of 1.5 seconds 

the display will show the stopwatch icon 

  pressing the select key 

 will 

display the test icon so testing can be repeated 

 

Summary of Contents for RP Check




























Reviews: