background image

3

ENG

Safety Instructions

Before you start exercising, be sure to read the entire user guide, especially the safety information, the maintenance & cleaning 

information and the training information. Take care too that everyone who uses this training device is also familiar with this infor-

mation and observes it.

Be sure to carefully follow the maintenance and safety instructions in this manual.

This training device may only be used for its specific purpose. Improper use may present a risk of accidents, damage to health or 

damage to the exercise device. No liability whatsoever is accepted by the distributor for injury or damage caused by improper use.

Power connection (only applies to devices with an external electrical connection)

 

A mains voltage of 220-230V is required for the operation of the device.

 

The exerciser may only be connected to a professionally installed, earthed, 16 A, fused single socket with the mains cable 

supplied.

 

The training device is switched on and off only using the ON / OFF switch.

 

Always disconnect the power plug from the power outlet when moving the exerciser.

 

Before carrying out any cleaning, maintenance or other work, always disconnect the mains plug from the socket.

 

When connecting the mains plug, do not use socket strips or cable reels.

 

If an extension cable is required, then it must comply with DIN standards, VDE regulations and guidelines, technical rules 

issued by other European Union member states or other states which are party to the Agreement on the European Economic 

Area.

 

Always lay the power cord in such a way that it can neither be damaged nor is a tripping hazard.

 

In operating or standby mode, electrical devices such as mobile phones, PCs, Televisions (LCD, plasma, tube, etc.), game 

consoles etc. will emit electro-magnetic radiation. For this reason, all these types of devices should be kept away from your 

training device as they could lead to malfunction, disturbances or false outputs being shown in heart rate measurements.

Training environment

 

Select a suitable space for your training device to provide an optimum amount of free space and highest level of safety. You 

should leave a free space of at least 100 cm in front of and behind the device and a minimum of 100 cm to each side of the 

training device.

 

Ensure good ventilation and that optimal oxygen is available during exercise.Avoid draughts.

 

Your exercise equipment is not suitable for outdoor use, so storage and training is only possible in temperate, clean dry 

rooms.

 

Do not operate or store your training device in wet areas, such as swimming pools, saunas, etc.

 

Make sure that your exercise equipment is always mounted on a level clean surface is. Unevenness in the ground must be 

removed or compensated.

 

To protect delicate floors, such as wood, lamina, tiles, etc. and from damage such as scratches, it is recommended to put a 

floor protection (carpet piece, mat, etc.) permanently under the device. Make sure that the pad is secured against slipping.

 

Do not place the exerciser on pale or white carpets, as the feet of the appliance may cause marks.

 

Make sure that your exercise equipment, including the power cord, does not come into contact with hot objects and there is a 

sufficient safety distance from any heat source, such as radiators, stoves, open fireplaces, etc.

Personal safety instructions for training

 

Remove the batteries or mains cable (if present) when the training device is not in use to avoid inappropriate or uncontrolled 

use by any other third party, e.g. children

 

You should make a health check with your doctor before your first workout.

 

If you feel any physical discomfort or experience breathing problems, stop training immediately.- Always start your workouts 

with a light load and increase it during the course of your workout evenly and gently. Reduce the load towards the end of your 

training session.

 

Be sure to wear suitable sportswear and sports shoes during exercise. Note that loose clothing can get caught in the running 

belt or rollers during exercise.

 

Your exercise equipment can only be used by one person at a time.

 

Check whether your device is in perfect condition before every training session. Never use your exerciser if it has any faults 

or defects.

 

Independent repair work can only be done after agreement and approval from our service department has been received. 

Only original spare parts may be used.

 

Your exercise equipment must be cleaned after each use. In particular, remove all residues caused by body perspiration or 

other liquids.

 

Always make sure that liquids (drinks, body sweats, etc.) never enter the vibrating plate or penetrate the cockpit, as this leads 

to corrosion and damage to the mechanical and electronic components.

 

Your exercise equipment is not suitable for use by children.

 

During training, third parties - especially children and animals - must have a sufficient safety zone.

 

Before any training, check whether there are objects under your training device and remove them. Never exercise with your 

exerciser when there are objects underneath.

 

Always make sure that your exerciser is not misused by children as a toy or climbing equipment.

 

Make sure that you and third parties never bring body parts close to moving mechanisms.

The construction of this training device is based on state-of-the-art technology and highest modern technical safety standards. 

This training device is to be used by adults only! Extreme misuse and/or unplanned training can cause damage to your health!

Summary of Contents for CX 5.1

































Reviews: