background image

KK-642.014 Rev.No:1  01.08.12                                                                                                                                                             Page | 17  

  

·By “2mA detection” function, in case of decreasing current which comes from detector or converter card, the 
system response is determined.  In this condition system may give fault warning, notification warning or 
cannot be counted as a warning status. 
·By “Warm-up delay” function, it is told to the control panel that, in the start –up session, the signals coming 
from the detectors cannot be evaluated by the panel. This is because detector will have more stable values 
after warm-up time. Hence they will measure accurate values. 

 

After adjusting these settings press 

“Down (-)” button to see the upcoming 3

rd 

screen. 

 

*** CHANNELS 

*** 

Channel 1 
configuration 

> Fire Reset Time : Alarm 

L1 Direction : Alarm L1 
On Threshold: Alarm L1 
Off Threshold: 

------------------------------------------------------------ 
Enter 

– OK 

Exit 

– Pre Menu 

 

·“Fire Reset Time”: Function that during fire alarm condition, when pressed to “Reset”, the determination of 
interruption time of the energy of the channel which detector connected to that channel is adjusted. 

 

· “Low  alarm  direction”:  Function  that  estimates  the  sensitivity  of  low  alarm  warning  as  increasing  or 
decreasing level of the gas in the medium. 
· “Low alarm opening level” Function that determines the threshold of  gas level of  the low alarm warning 
value. 

 

·“Low  alarm  closing  level”:  Function  that  determines  the  gas  level,  when  panel  pass  from  low  alarm  to 
warning to normal status. 

 

After adjusting these settings press 

“Down (-)” button to see the upcoming 4

th 

screen. 

 

*** CHANNELS 

*** 

Channel 1 
configuration 

> 2

nd 

level Alarm Direction: 

2

nd 

level Alarm Input Value: 

 

------------------------------------------------------------ 

Enter 

– OK 

Exit 

– Pre Menu 

 

·“High  alarm  direction”  Function  that  estimates  the  sensitivity  of  high  alarm  warning  as  increasing  or 
decreasing level of the gas in the medium. 
·“High alarm opening level” Function that determines the threshold of gas level of the high alarm warning 
value. 

Summary of Contents for MG-400





















Reviews: