background image

 

                           Orion ISS 

This  Installation  Manual  contains  the  instructions  that  must  be  followed  for  proper  installation 
and commissioning the S2000-IPDL detector. 
The detector is described and the rules to adjust and operate it are discussed in the User’s 
Manual  (which  can  be  found  at  the  site  of  the  Bolid  Company 

http://bolid.ru

  in  the  section 

PRODUCTS at the page of S2000-IPDL). 

1  SAFETY PRECAUTION 

 

-

  The detector is a source of danger neither for human nor for protected material 

assets (including the emergency situations). 

-

  The  design  and  circuitry  of  the  detector  ensure  its  fire  safety  during  operation 

(including emergency operation). 

-

  As  to  methods  of  human  protection  against  electric  shock,  the  detector  meets 

the requirements of Class III as per Russian GOST 12.2.007.0. 

-

  In  terms  of  voltage  values,  the  detector  is  not  dangerous  to  human  life  and 

health, but during repair, inspection, installation, and operation it is necessary to 
comply  with  safety  measures  in  accordance  with  Regulations  for  Operation  of 
Consumers’  Electrical  Installations  and  Safety  Rules  for  Operation  of 
Consumers’ Electrical Installations. 

-

  While  installing  and  maintaining  the  detector  please  comply  with  the  rules  for 

working at heights. 

2  MOUNTING 

2.1  The units of the detector should be attached to the building structures generally with the 
help of mounting kits supplied: 

Kit No.1:  Designed to attach the transceiver unit and to fasten the housing additionally (if 
necessary) on completing commissioning. 

Kit No.2:  Designed  for  attaching  an  S-Type  (small)  reflector  or  a  remote  indicator  and 
control unit. 

Kit No.3:  For an XS-Type (extra small) reflector. 

Kit No.4:  For an L-Type (large) reflector. 

In  specific  situations  (for  example,  when  the  detector  components  can  be  fastened  only  by 
means  of  threaded  joints)  another  fixture  elements  can  be  used.  Anyway,  it  is  necessary  to 
provide reliable fastening without gaps, drifting, and any motion of the detector’s elements while 
in operation. 

Addressable 

Reflective 

Beam Smoke Detector 

 

S2000-IPDL 

Installation Manual 

 

Summary of Contents for S2000-IPDL









Reviews: