background image

BLADE

2-1

TI215G0010

General Information - Safety 

!

To operate the machine in any operating 

condition, including maintenance, it is not 

necessary that more than one person be 

present. Using more than one person is 

superfluous and, however, it is not allowed 

for safety reasons.

!

The employer should instruct the staff on the 

accident risks, on safety devices and on the 

general rules concerning prevention and 

protection as set out by the European Community 

Directives as well as by the laws of the Country 

where the machine has been installed.

The operator must know the position and the 

operation of all the commands and the characteristics 

of the machine. The operator should also have read 

this entire manual.

Only qualified engineers should carry out the 

interventions for maintenance after having duly 

prepared the machine.

!

Any unauthorized tampering or replacing of 

one or more parts of the machine, adopting 

accessories that change the use of the 

machine and the use of manufacturing 

materials other than those recommended in 

this manual, can be potential accident risks. It 

is strictly forbidden for the machine to be 

operated by two people at the same time, one 

inside the guards and the other the control 

push-button panel.

DANGER AND RESIDUAL RISKS

During design, all the areas at risk were taken into 

consideration, and therefore all of the necessary 

precautions have been taken to avoid risks to people, 

and damage to the machine components. In order to 

guarantee both the health and safety of those exposed, 

the machine has been provided with special safety 

devices:

 

– EMERgENCY push-button to immediately stop the 

machine and STOP devices on the push-button panel 

of the control device;

 

– Fixed guards: these are mounted in areas for exclusive 

access for standard maintenance. They are fixed with 

systems that require specific tools to remove them or 

have been screwed in;

 

– Protection and segregation of the electrical/

electronic equipment of the machine with a 

metallic container to avoid accidental contact with 

the equipment under voltage in the event that the 

metallic container is open; protection of the electrical 

cabin: IP 54; protection of inner equipment IP 20 

against accidental contact;

 

– Adequate panels or protection to cover moving 

elements;

 

– Electrical devices to detect supply failures of the 

machine and the malfunction of electrical devices of 

motors.

!

wARNING !!! 
For compressors equipped with INvERTER, 

before performing any maintenance job, wait 

at least 5 minutes after you have disconnected 

the electricity supply. 

!

wARNING !!! 

Our machine should not be used in areas 

where  the environment is potentially 

explosive.

After having carefully considered all possible risks 

concerning the use and maintenance of the machine, 

the solutions necessary to remove the risks and limits 

the dangers to those exposed have been adopted.

Although the machine is equipped with safety devices, 

the following residual risks remain:

 

– Risk of bruises, tearing, cuts during the handling of 

tools and/or elements;

 

– Risk of bruises during machine intervention. 

OpERATION

 

– The operator should use the personal protection 

devices; 

 

– Use the compressor only for the kind of application 

for which it has been planned (air compression for 

industrial use);

 

– Before starting, ensure that the compressor has oil;

 

– For the oil type to be used, please refer to Section 10 

of this manual;

 

– Never operate the compressor if there is a possibility 

of inhaling smoke or toxic or flammable vapors; 

 

– Never operate the compressor at pressures higher 

than those indicated on the ID plate. The air 

delivered directly by the compressor, filtered and 

purified from oil, cannot and must not be used for 

breathing; 

 

– If hoses are used to distribute air, ensure that they 

are of a proper size and adequate to the working 

pressure and that they are neither damaged nor 

worn. Please remember that rubber hoses should be 

replaced at regular intervals; 

 

– Never remove the oil inlet plug when the machine 

is running or there is still pressure inside the 

compressor: there would be a leak of hot oil; 

 

– Please note that the machine, although it has an 

acceptable sound pressure level, can produce a 

much higher noise if the room for its installation 

is narrow and reverberating. It should be noted 

Summary of Contents for BLADE - Plus 15 H

























































Reviews: