background image

Generation II Entree Bath 

 

All Models 

INSTALLATION MANUAL 

06-23-17 

Page 11 of 11

2071 14

th

 Ave – Columbus, NE 68601 

 800-798-5867  FAX: 402-563-9102 

www.mastercarebath.com

1. Wall Placement

MB-68-AV 36” D x 65 ½” W x 46 ½” H 

MB-68-AV (XL) 36” D x 71 ½” W x 46 ½” H 

5. Foot End Peninsula Placement

MB-68-AVF 36” D x 62 ½” W x 46 ½” H 

MB-68-AVF (XL) 36” D x 68 ½” W x 46 ½” H 

Requires Back Door Panel

 

2. Foot End Corner Placement

MB-68-AVF 36” D x 62 ½” W x 46 ½” H 

MB-68-AVF (XL) 36” D x 68 ½” W x 46 ½” H 

3. Head End Corner Placement

MB-68-AVH 36” D x 62 ½” W x 46 ½” H 

MB-68-AVH (XL) 36” D x 68 ½” W x 46 ½” H

 

4. Alcove Placement

MB-59-AV 36” D x 59 ½” W x 46 ½” H 

MB-59-AV (XL) 36” D x 65 ½” W x 46 ½” H 

Finished Alcove opening must be a minimum of 

60" for Standard length and 66" for XL length. 

6. Head End Peninsula Placement

MB-68-AVH 36” D x 62 ½” W x 46 ½” H 

MB-68-AVH (XL) 36” D x 68 ½” W x 46 ½” H 

Requires Back Door Panel

 

7. Island Placement

MB-68-AV Gen II Entrée Bath 36” D x 65 ½” W x 46 ½” 

MB-68-AV (XL) Gen II Entrée Bath 36” D x 71 ½” W x 46 

Requires Back Door Panel

 

 

ISLAND AND PENINSULA PLACEMENT CONFIGURATION 

Dimensions listed here are actual tub dimensions, not space requirements. 

Summary of Contents for Entree Gen II















Reviews: