background image

Generation II Entree Bath 

 

All Models 

INSTALLATION MANUAL 

06-23-17 

Page 7 of 11

2071 14

th

 Ave – Columbus, NE 68601 

 800-798-5867  FAX: 402-563-9102 

www.mastercarebath.com

5.

Flush line into a bucket 

and verify hot water comes from that hose. After flushing, attach tub hose with red

marking.

6.

Make sure the screen is in the hose.

7.

Connect a flexible hose to the hot water supply valve.

8.

Flush hose into a bucket 

and verify cold water comes from hose. After flushing, attach tub hose with blue marking.

Note: The mixing valve will not perform correctly if those hoses are connected backwards.

9.

Make sure the screen is in the hose.

10.

Connect a flexible hose to the cold water supply valve.

11.

Turn on the hot and cold supply valves slowly

 and verify there are no leaks.

12.

Place the tub in the final desired location and connect the drain tubing

 as shown in the following figure.

Note: The "U" section must be installed "low profile" so that it will clear the tub door when in open position. The reason

for the "U" configuration is for ease of disconnection in the event the tub needs to be slid out for service.

 

MEMO:

 

1.

Parts shown in the top view of

this suggested layout are to be

supplied by the installing

contractor.

2.

All drain connecting parts

supplied by the contractor

must meet National and State

Plumbing Codes. 

3.

If floor sink used, it must be at

least three inches in diameter. 

4.

If rubber coupler does not

meet code, use any type of

detachable coupler that meets

code to  allow drain assembly

to be uncoupled so tub can be

slid out for service.

Wall 

Drain 

Option 

Floor 

Drain 

Option 

40 

1

/

2

Re

ar

 W

al

Casual Water 

Drain Hose 

19" 

SIDE VIEW OF DRAIN 

CAUTION

:

 

Plumbing and 

electrical installations must be 

clear of the full rotational arc of 

the door to the back of the tub.

 

1

1

/

4

" off to floor 

Rear Tub 

Service Panel 

L

eft Rear tub leg 

2” 90 PVC close ST 

EL connected to 2” 

tub drain located 

on left rear tub leg 

2” rubber coupler 

- see item # 4 in 

memo below 

2” PVC pipe cut to 

length on job site 

2" 90

° 

 PVC EL SxS 

10” From wall 

to center line 

of 2” drain 

22” 

2” 90 PVC Close 

ST EL connected 

to the 2” floor 

drain female 

 

2” PVC pipe cut to 

length on job site 
2” rubber coupler 

- see item # 4 in 

memo below

2” 90

° 

 PVC Close ST EL

Note

: This "U" portion 

of drain must be 

installed low 

profile to keep 

from interfering 

with tub door.

 

Center Line 

of Tub 

End to End

Note

: Use a straight 90

° 

PVC 

elbow to run to a floor drain

 

2" PVC 

pipe cut 

to length 

on job site 

2" PVC Tub Drain 

Support Strap 

Rear Left Tub Leg 

Side of Tub 

FRONT VIEW 

TOP VIEW 

Floor

Rear Tub Lower Service Panel 

Tub Drain Valve

 

Summary of Contents for Entree Gen II















Reviews: