manualshive.com logo in svg

Master Spas Bar Harbor, Owner'S Manual

Share
Download
Master Spas Bar Harbor Owner'S Manual Download Page 67

America’s Leader In Luxury

M A S T E R   S P A S

67

REGULAR MAINTENANCE PROCEDURES

Note:
These are areas that will require the spa owner to perform routine 
maintenance.These are not areas covered under the warranty 
of the spa.

CLEANING JETS

The majority of jets in your spa can individually be turned on/off. If any of 
these jets become hard to turn, it will be necessary to remove the jet to clean
it as grit/sand and mineral deposit may be present.
Jets in the Master Spa line are removed by turning the grey collar counter 
clockwise and then pulling out the jet.
Most jets in the Down East and Freedom Spas can be removed by turning the 
collar clockwise, then pulling the jet out.The smallest jets in the Down East 
line are removed by turning the collar counter clockwise and then pulling the
jet out.The smallest jets in the Freedom Spa line are fixed and cannot be 
removed.

TO CLEAN JETS

Place the jet(s) in a bucket, fully immerse in white vinegar. Let the jet(s) soak
overnight and then rinse with water. Reinstall the jet(s). It may also be 
necessary to clean the grit/deposit from the white jet body using an old 
toothbrush.

CLEANING DIVERTER VALVES

Some Master Spas, Down East Spas, and Freedom Spas have diverter valves.
Due to mineral deposits and grit/sand that may get into the internal parts of 
the diverter valve, it may become hard to turn or freeze up totally. In this 
case, it is necessary to remove the handle and cap of the diverter valve. Before 
proceeding, make sure the power to the spa is turned off. (cont. next page)

MS Owners Manual  12/5/03  2:06 PM  Page 67

Summary of Contents for Bar Harbor









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands