background image

America’s Leader In Luxury

M A S T E R   S P A S

46

DOWN EAST (2 -3 PUMP SYSTEM)

Clean-up Cycle

When the pump is turned on by a button, a clean-up cycle begins 30 
minutes after the pump is turned off or times out. The pump and the 
ozone generator will run for one hour.

Ozone

(optional)

On most systems, the ozone generator (if installed) runs during filter cycles
(except when pump 1 is operating at high speed on a non-circ system) and during
clean-up cycles.

Your system is configured with the ozone disable feature, the ozone generator will
turn off for 1 hour anytime a function button (Jets 1, Jets 2, etc.) 
is pressed.

Freeze Protection

If the temperature sensors detect a drop to 44˚F (approximately 6.7˚C) 
within the heater, the pump automatically activates to provide freeze protection.
The equipment stays on until 4 minutes after the sensors detect that the spa tem-
perature has risen to 45˚F (approximately 7.2˚C) or higher.

*15-minute timeouts may be changed to 30 minutes and 2-hour timeouts may be 

changed to 4 hours. • Consult your dealer for more information.

MS Owners Manual  12/5/03  2:04 PM  Page 46

Summary of Contents for Bar Harbor









































































Reviews: