background image

 

 

 

S

AFETY INFORMATION

 

1

 
 
 

 

Warning:   This product is for professional use only!  

        It is not designed for household use. 

 

This product is designed exclusively for use with the Martin Atomic 3000 DMX unit. Use the 
device only as intended.    
The Atomic 3000 DMX presents risks of lethal or severe injury due to fire and heat, electric 
shock, ultraviolet radiation, and falls. Flashing light is also known to trigger epileptic seizures in 
persons who are photosensitive. Please review the important safety information in the Atomic 
3000 DMX user manual. 

Read this manual

 before powering or installing the fixtures, follow the safety precautions listed 

below and observe all warnings in this manual. 
If you have questions about how to operate the fixtures safely, please contact your Martin dealer 
or call the Martin 24-hour service hotline at +45 70 200 201. 

 

Atomic Colors: Safety instructions. 
 

Before using this unit please read this manual completely, 

and refer to the user manual for Atomic 3000 DMX strobe.

 

General 

 

• 

Read this manual fully before starting to use the unit. 

• 

Ensure that no objects or items are near the front aperture, or can get trapped in the roller 
mechanism. 

• 

Make sure the power supply for the Atomic Colors is connected and switched on, 

before 

operating the Atomic strobe.

 

 

To guard against falls 

 

• 

When fitting the unit to the Atomic 3000DMX, ensure all screws are thoroughly re-tightened. 

• 

When rigging the unit, use the safety wire attached to the unit as a means of secondary 
attachment. 

Note: This safety wire is designed solely for use with the Atomic Colors unit. Use a 
separate safety wire for Atomic 3000DMX strobe, and any other pieces of equipment. 

• 

When suspending the fixture above ground level, verify that the structure can hold at least 10 
times the weight of all installed devices. 

• 

Verify that all external covers and rigging hardware are securely fastened and use an 
approved means of secondary attachment such as a safety cable. 

• 

Block access below the work area whenever installing or removing the fixture. 

 

To guard against epileptic seizure 

 

• 

Do not operate the fixture near stairways. 

• 

Provide advance notice that strobe lighting is in use. 

• 

Avoid extended periods of continuous flashing, particularly at frequencies of 10 to 20 flashes 
per second, or with the color red. 

Atomic Colors User Manual                         Safety Information 

4

Summary of Contents for Atomic Colors


























Reviews: