background image

Harness 3: White 5-Pin Mini Connector 

(continued)

Pink Wire: (continued)

Start Status: (Shock Sensor Bypass Control) Output: (See Alarm Feature Stage 3 Programming)

This wire is designed to bypass the shock sensor while remote start is operating. This wire will also supply an output

for an additional 3 seconds after the remote start unit is turned off.

Gray Wire: Channel 2 (Trunk

Release) Output

This will become a 1 second pulse

ground by activating channel 2 on

transmitter for two seconds, the

current capacity of this wire is

200mA. This feature allows you to

remote control trunk release or other

electric device.

Harness 4: 7-Pin Mini Black Connector 

Blue Wire: (-) Negative Instant Trigger Input

This wire is the ground trigger input wire for hood/trunk pin switches.

Green Wire: (-) Negative Door Trigger

This wire is the ground trigger input wire for negative door pin switch.

Violet Wire: Positive Door Trigger

This wire is the positive trigger input wire for positive door pin switch.

White/Black Wire: Negative Safety Shut Down Input

The White/Black wire provides an instant shutdown for the remote start, whenever it is grounded. Connect the wire

to the hood pin switch previously installed. this wire must be routed through a grommet in the firewall and

connected to the hood pin switch. If the pin switch is to be used with an alarm system, connect this wire with

diode. Diodes are required when the hood pin is used as a triggering device. Wire as shown.

Important!

This connection is a

safety wire and must be connected

as shown and tested as specified.

Failure to do so may result in

personal injury or property damage.

See detail or wiring in the following

diagram. This wire may also be used

if the vehicle brake light circuit

switches ground to the brake lights.

An isolation diode must be used for

ground switched brake light circuits

and must be connected to the output

of the brake switch.

Wiring

8

87

86

85

30

(Relay Not Supplied)

Output to Power

Trunk Switch

To Co12 Volts

Input to Relay (+ or -)

White 5-Pin

Mini

Connector

Gray

Wire

Hood Pin Switch

White/Black Wire

Negative Safety

Diode

Diode

To Alarm Instant

Trigger Blue Wire

Black 7-Pin

Mini Connector

M7A-IM  6/22/06  4:53 PM  Page 8

Summary of Contents for M7a





























Reviews: