background image

12 

 In accordance with the road safety regulations (Regulation of the Minister of 
Infrastructure of 31.12.2002. Journal of Laws No. 32 of 2002 item 262) 

– 

a unit 

consisting  of  an  agricultural  tractor  and  the  agricultural  machinery  that  is 

coupled with it must meet the same requirements as the tractor. 

 

NOTE!  The  unit  as  a  part  of  the  vehicle  protruding  beyond  the  rear  side 

contour  of  the  tractor  obscuring  the  rear  lights  of  the  tractor  poses  a 
danger  to  other  vehicles  on  the  road.  It  is  forbidden  to  travel  on  public 
roads without appropriate markings.

 

 

The manufacturer does not supply warning signs as standard equipment on the machine. 

Warning signs are available commercially. The warning boards must be securely mounted 
in the brackets and the plug connected to the socket of the tractor's electrical system. 
Check the operation of the lights before starting the transport. After lifting the machine, 
check the clearance under the lowest working elements, which should be at least 25 cm. 
The permissible transport speed of the tractor with the machine is 15 km/h. It should be 
reduced to  10  km/h  on  roads  with poorer surfaces  and  5  km/h  on  dirt  roads.  Extreme 
caution  should  be  exercised  when  passing  and  overtaking  other  vehicles,  avoiding 
obstacles and crossing large irregularities in fields and dirt roads. 

 

3.5 Description of residual risk 

  

Mandam Sp. z o.o. makes every effort to eliminate the risk of accidents. There is, 

however,  a  residual  risk  that  could  result  in  an  unfortunate  accident.  The  greatest 
danger occurs when: 

 

using the machine for purposes other than those described in the instructions, 

 

using the machine by minors, persons who are not authorised, who are ill or who 

are under influence of alcohol or other drugs, 

 

persons and animals within the operating range of the machine are present, 

 

no caution is paid when transporting and manoeuvring the tractor, 

 

staying on the machine or between the machine and the tractor while the engine 

is running, 

 

operating and failure to comply with operating instructions, 

 

driving on public roads. 

 

3.6 Assessment of residual risk 

  

Residual risk can be minimised by applying the following recommendations: 

 

prudent and unhurried operation of the machine, 

 

careful reading of operating instructions, 

 

keeping a safe distance from danger zones, 

 

prohibition  on  being  on  the  machine  and  in  the  operating  area  of  the  machine 

while the tractor engine is running, 

 

carrying out maintenance work in accordance with safety rules, 

 

use of protective clothing and, if working under machinery, a helmet, 

 

prevention of unauthorised access to the machines, especially by children. 

4. Information on handling and use 

Before starting the machine for the first time: 

 

refer to the operating instructions, 

Summary of Contents for SAL DISC HARROW




























Reviews: