Malaguti F12R AIR 50 cc. - Euro 2 Workshop Manual Download Page 40

Page: 40 / 46

0.07

F12R L.C. 50 cc.

Signalling System

Chapter

paGe

ISSUe

NOTE: every time the sensor closes (V

), the system activates the alarm procedure, which consists

in the oil icon lighting up on the display along with the relative red warning light. The system

will in any case remain fully operative. To avoid false alarms, this message appears only if

the contact remains closed in positive mode for at least 15 seconds.

The alarm is displayed irrespective of the function selected.

F. 49

If the fuel level signal is not correct, check:

1) reSIStaNCe OF FUeL prOBe
) CONtINUItY OF GreY CaBLe

F. 0

F. 1

- NOTE: the information is displayed in graphic form by means of a bar graph with eight segments

located on the bottom right of the display and accompanied by the “fuel” icon.

- CAUTION: the relative icon will start flashing if the probe is not connected.

Summary of Contents for F12R AIR 50 cc. - Euro 2















































Search results

Summary of Contents for F12R AIR 50 cc. - Euro 2

Reviews:

Related manuals for F12R AIR 50 cc. - Euro 2

Brands by name

Popular brands

Malaguti F12R AIR 50 cc. - Euro 2, Workshop Manual

Search results

Summary of Contents for F12R AIR 50 cc. - Euro 2

Reviews:

Related manuals for F12R AIR 50 cc. - Euro 2

Brands by name

Popular brands