background image

5

1.1 GENERAL PRECAUTIONS BEFORE USAGE 

Check that the area if it  complies with the technical requirements for 

chimney

connection

,water and electrical installation.

For safety and safe use of electrical installation, make sure that the

installation has a

 proper

 earth 

connection

 with isolation  and that the 

earth

 line

is

 

not phase-misplaced.

Your pellet boiler is guaranteed for 2 (two) years against material and

manufacturing defects, providing that the warnings and standards stated in the

operating instructions are followed.

 

The manufacturer is not responsible for

 

any

faults or damages of the product results  from unintentional, incorrect or

unintended use  that are against 

the

 instructions.

Do not misuse the boilers. Our boilers are manufactured to provide hot water

(max. 90 

°C

) to the heating system.

Permanent fresh air should be supplied to the area where the device is

installed. For safety, it is strictly forbidden to install boilers in enclosed spaces

where people live.

Do not operate boilers without water. Never make a cold water supply to a

 

hot

boiler. If the boiler temperature has risen above 90

°C

 for any reason,

 

do

 

not

cool the boiler and do not supply cold water to increase the water level

 

until

 

the

boiler temperature decrease below 40

°C

.

Water at the installation should not be discharged except for repair and frost

hazard. Anti

-

freeze can be added to the installation water at a rate of 15%

against frost hazard.

When the boiler is running, the difference between the flow and return water

should be at most 20

°C

.

Water that has h

igh amount of lime are extremely inconvenient for boilers

 

and

installations. In such cases it is necessary to use

 water

 softening devices.

Defects that may occur as a result of water leaks or blockages due to lime in

the boiler are not covered by the warranty.

Every year before the heating season, the boiler body, chimney connection

pipes and chimney must be controlled and cleaned. In this way, the system

 

can

be operated more efficiently.

Water should never be taken from the boiler for domestic use.

Summary of Contents for 25 MKP


























Reviews: