background image

3

15 Meters

SAFETY INSTRUCTIONS

General Instructions

Read this instruction manual to become familiar with handling of the 

 

well as others due to improper handling.

It is recommended only to lend the equipment to people who have proven to 

 

be experienced.
Always hand over the instruction manual.

First users should ask the dealer for basic instructions to familiarize oneself 

 

with the handling of brushcutters.

Children and young persons aged under 18 years must not be allowed to 

 

operate this equipment. Persons over the age of 16 years may however 
use the device for the purpose of being trained while under supervision of a 

Use with the utmost care and attention.

 

Operate only if you are in good physical condition. Perform all work calmly 

 

and carefully. The user has to accept liability for others.

Never use this equipment after consumption of alcohol or drugs, or if feeling 

 

tired or ill.

National regulation can restrict the use of the machine.

 

Intended use of the machine

This equipment is only intended for cutting grass, weeds, bushes, 

 

undergrowth. It should not be used for any other purpose such as edging or 
hedge cutting as this may cause injury.

Personal protective equipment

The clothing worn should be functional and appropriate, i.e. it should be tight-

 

could become entangled with bushes or shrubs.

In order to avoid either head-, eye-, hand-or foot injuries as well as to protect 

 

your hearing the following protective equipment and protective clothing must 
be used during operation.

Always wear a helmet where there is a risk of falling objects. The protective 

 

helmet (1) is to be checked at regular intervals for damage and is to be 
replaced at the latest after 5 years. Use only approved protective helmets. 

The visor (2) of the helmet (or alternatively goggles) protects the face from 

 

prevent eye injuries.

Wear adequate noise protection equipment to avoid hearing impairment (ear 

 

muffs (3), ear plugs etc.).

 

We strongly recommend that the user wears work overalls.

Gloves (5) are part of the prescribed equipment and must always be worn 

 

during operation.

When using the equipment, always wear sturdy shoes (6) with a non-slip 

 

sole. This protects against injuries and ensures a good footing.

Starting up the brushcutter

Please make sure that there are no children or other people within a working 

 

range of 15 meters (50 ft), also pay attention to any animals in the working 
vicinity.

Before use always check the equipment is safe for operation:

 

Check the security of the cutting tool, the throttle lever for easy action and 
check for proper functioning of the throttle lever lock.

Rotation of the cutting tool during idling speed is not allowed. Check with your 

 

dealer for adjustment if in doubt. Check for clean and dry handles and test 
the function of the start/stop switch.

Summary of Contents for EM4351UH





























Reviews: