background image

23

 

If oil cap is not tightly secured, it may leak.

CLEANING OF AIR CLEANER

WARNING:

and do not smoke.

Interval of Cleaning and Inspection: Daily (every 10 operating hours)

Turn the choke lever to the full close side, and keep the carburetor off from 

 

dust or dirt.

Removing air cleaner cover

Release the hook on the air cleaner cover by pressing down the loop on the 

 

plate.

 

Pull and remove the air cleaner cover.

 

Cleaning element 

Remove the elements and tap them to remove dirt.

 

For heavy contamination:

 

1)  Remove the element (sponge), immerse it in warm water or in water-

diluted neutral detergent, and dry it completely. Do not squeeze or rub it 
when washing.

2)  Clean the element (paper) by tapping it gently. If you can use an air blow 

gun, blow the compressed air onto the inside of the element (paper). Do 
not wash the element (paper).

Before attaching the element (sponge), be sure to dry it completely. 

 

Wipe out oil adhering around the air cleaner cover and separator plate with 

 

waste cloth.

Attaching air cleaner cover

Fit the element (sponge) and element (paper). Insert the element (sponge) all 

 

the way into the air cleaner cover.

Insert the side hook onto the air cleaner cover as illustrated, and push the 

 

lower part of the air cleaner cover until it clicks so that the hook sits into the 

NOTICE:

Clean the elements several times a day, if excessive dust adheres to it. 

 

Remove oil on the elements. If operation continues with the elements 

 

remaining not cleared of oil, oil in the air cleaner may fall outside, resulting 
in contamination of the environment.

Do not put the elements on the ground or dirty place. Otherwise they pick 

 

up dirt or debris and it may damage the engine.

Never use fuel for cleaning the elements. Fuel may damage them.

 

Plate

Element (sponge)

Air cleaner cover

Air cleaner cover

Element (sponge)

Separator plate

Element (paper)

Loop

Fixing bolt

POINTS ON OIL

Never discard replaced engine oil in garbage, earth or sewage ditch. 

 

Disposal of oil is regulated by law. In disposal, always follow the relevant 
laws and regulations. For any points remaining unknown, contact 
Authorized Service Agent.

Oil will deteriorate even when it is kept unused. Perform inspection and 

 

replacement at regular intervals (replace with new oil every 6 months).

Side hook

Hook

Summary of Contents for EM4351UH





























Reviews: