17 ENGLISH
The chip receiver gathers discarded leaves and makes clean-up
afterward much easier. It can be installed on either side of the tool.
To install the chip receiver, put and press the chip
receiver onto the shear blades so that the hooks fit into
the grooves on the shear blades.
►
Fig.25:
1.
Hook
►
Fig.26:
1.
Hook
NOTICE:
Make sure that the chip receiver does
not overlap the branch catcher.
►
Fig.27:
1.
Branch catcher
To remove the chip receiver, press the levers on both
sides to release the hooks.
►
Fig.28:
1.
Lever
NOTICE:
Never try to remove the chip receiver
by an excessive force with its hooks locked in the
grooves of the shear blades.
OPERATION
Attaching the shoulder harness
Optional accessory for DUN500W
CAUTION:
Before operation, make sure that
the shoulder harness is properly attached to the
hanger on the tool.
NOTE:
Use the shoulder harness attached to the tool.
Before operation, adjust the shoulder harness accord
-
ing to the user size to prevent fatigue.
1.
Wear the shoulder harness on your shoulder.
►
Fig.29
2.
Clasp the hook on the shoulder harness to the
tool's hanger.
►
Fig.30:
1.
Hook
2.
Hanger
3.
Adjust the shoulder harness to a comfortable working position.
►
Fig.31
The shoulder harness features a means of quick release.
Simply squeeze the sides of the buckle to release the
tool from the shoulder harness.
►
Fig.32:
1.
Buckle
Operating the tool
WARNING:
Do not use the tool near any
electrical power lines.
Contacting with power lines
or using the tool near power lines may cause serious
injury or electric shock resulting in death.
WARNING:
Keep hands away from shear
blades.
WARNING:
Be extremely careful to maintain
control of the tool at all times. Do not allow the
tool to be deflected toward you or anyone in the
work vicinity.
Failure to keep control of the tool
could result in serious injury to the bystander and the
operator.
CAUTION:
Avoid operating the tool in very
hot weather as much as practicable. When operat
-
ing the tool, be careful of your physical condition.
CAUTION:
Be careful not to accidentally
contact a metal fence or other hard objects while
trimming.
The shear blades may break and cause
an injury.
CAUTION:
Be careful not to allow the shear
blades to contact the ground.
The tool may recoil
and cause an injury.
CAUTION:
Overreaching with a hedge trim
-
mer, particularly from a ladder, is extremely
dangerous.
Do not work while standing on anything
wobbly or infirm.
NOTICE:
Do not attempt to cut branches thicker
than 10 mm in diameter with the tool.
Cut branches
to 10 cm lower than the cutting height using branch
cutters before using the tool.
►
Fig.33:
(1)
Cutting height
(2)
10 cm
NOTICE:
Do not cut down dead trees or similar
hard objects.
Doing so may damage the tool.
NOTICE:
Do not trim the grass or weeds while
using the shear blades.
The shear blades may
become tangled in the grass or weeds.
Hold the tool with both hands.
For DUN500W
►
Fig.34
For DUN600L
►
Fig.35
Pull the switch trigger while pressing the lever, and then
move the tool forward.
►
Fig.36
For basic operation, tilt the shear blades toward the
trimming direction and move it calmly and slowly at the
speed rate of 3 to 4 seconds per meter.
►
Fig.37
To cut a hedge side evenly, cut from the bottom to top.
►
Fig.38
When trimming to make a round shape (trimming box-
wood or rhododendron, etc.), trim from the root to the
top for a beautiful finish.
►
Fig.39
If the chip receiver is attached to the shear blades, it
gathers discarded leaves and makes clean-up after-
ward much easier.
►
Fig.40
Summary of Contents for DUN500W
